Canada version. Canadian metric rebar (10M, 15M, 20M to CSA G30.18), HSS and metric W-shape sizes, kg and lb side by side, and prices in CA$. US version

Steel Weight Calculator (Canada)

Weight of 10M, 15M and 20M rebar, HSS, metric W-shapes, flat bar and plate in kg/m and lb/ft for a full order, with CSA G30.18 bar masses and prices in CA$.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Steel Weight Calculator?

Canadian rebar is sized by area, not diameter. A 10M bar has a nominal area of 100 mm², 15M 200 mm² and 20M 300 mm², and CSA G30.18 bar tables give their masses as 0.785, 1.570 and 2.355 kg/m, which is simply the area times 7,850 kg/m³. To reproduce those figures here, enter the diameter of a round bar with the same area: 11.284 mm for 10M, 15.958 mm for 15M and 19.544 mm for 20M. A bundle of 100 bars of 10M at 6 m then weighs 471 kg.

Structural steel in Canada is designated in metric even when the shapes are rolled to US sizes: a W200x27 is the same section as a W8x18, with the nominal mass in kg/m in its name. Hollow sections are HSS to CSA G40.21 or ASTM A500 and are listed by outside size and wall in millimetres. The calculator works in either system and always shows kg and lb together, which helps when a drawing is metric and the supplier quotes in pounds.

For rolled W-shapes the calculator leaves out the root fillets, so it comes in a little light (26.2 kg/m for W200x27 from its 207 x 133 mm size, 5.8 mm web and 8.4 mm flange). Use the handbook or mill figure for billing and the calculator for flats, plate, HSS and quantities.

  • Plate, flat, round, square and hex bar, round tube, SHS, RHS, angle, channel and I-beam
  • EN 10219 and EN 10210 corner radii for hollow sections, or sharp corners
  • Weight per metre and per foot, per piece and in total, in kg and lb
  • Density presets for carbon and stainless steel, cast iron, aluminium, copper, brass and titanium, all editable
  • Comparison table for every material, surface area for coating, optional cost
Read the guide: Steel Weight Formulas for Plate, Bar, Pipe and Sections (kg/m and lb/ft)

Updated

How to use the Steel Weight Calculator

  1. Choose metric (mm, m, kg) or imperial (in, ft, lb). Switching converts the sizes you already entered.
  2. Pick the shape and enter its dimensions. Tubes need the outside size and the wall thickness.
  3. For square or rectangular tube, choose cold-formed, hot-finished or sharp corners.
  4. Enter the length of each piece and the quantity, then pick the material or type a density.
  5. Read the total, the weight of each piece, the weight per metre or foot and the surface area; add a price per kg or lb for a cost.

Worked examples

100 bars of 10M at 6 m

Input

Round bar 11.284 mm (100 mm²), 6 m, quantity 100

Output

0.785 kg/m; 4.71 kg each; 471 kg (1,038 lb)

Matches the CSA G30.18 mass of 0.785 kg/m exactly, because the diameter was chosen to give the 100 mm² nominal area.

100 bars of 15M at 6 m

Input

Round bar 15.958 mm (200 mm²), 6 m, quantity 100

Output

1.570 kg/m; 942 kg

Entering 16 mm, the rounded diameter often quoted for 15M, gives 947 kg instead: 0.5% heavy, which adds up over a large order.

HSS 152 x 152 x 6.4, 6 m

Input

Square tube 152 x 6.4 mm, cold-formed corners, 6 m

Output

28.16 kg/m; 169 kg

With hot-finished (Class H) corners the same size is 28.91 kg/m. Check the HSS class on the drawing; it also changes the column resistance under CSA S16.

Background and insight

Weight is simply cross-section area times length times density. The area formulas are exact for the idealised shapes: a round tube is π(D − t)t, an angle is t(a + b − t), and a hollow section with rounded corners is 2t(B + H − 2t) − (4 − π)(ro² − ri²). The ASME B36.10 pipe weight formula, 10.69(D − t)t in lb/ft with inches, is the same equation with the steel density folded in.

Carbon steel is taken as 7,850 kg/m³ (0.2836 lb/in³), the value EN 10025 and most section tables use. Stainless grades are heavier: EN 10088-1 gives 7,900 kg/m³ for 1.4301 (304) and 8,000 kg/m³ for 1.4401 (316). Aluminium alloys are about 2,700 kg/m³, copper C11000 about 8,890 kg/m³ and cartridge brass about 8,530 kg/m³. All of these are typical values at room temperature; enter your supplier's figure if it differs.

Real stock is never exactly nominal. Mill tolerances on plate thickness and bar diameter (EN 10029, ASTM A6) allow a few percent either way, and rolled beams, channels and angles have root fillets that add a little area. Use the theoretical weight for estimating and quoting, and the certified weight on the delivery note for lifting plans.

Common use cases

  • Quoting fabrication jobs

    Total the weight of plates, tubes and sections in a frame to price material and galvanising.

  • Lifting and transport

    Check that a bundle of bar or a stack of plate is within a crane, forklift or trailer limit.

  • Comparing materials

    See how much an aluminium or stainless version of the same part weighs before redesigning.

  • Estimating dead load

    Get kg per metre of a beam or rail to add self-weight to a structural load calculation.

Tips and limitations

  • Bar masses: 10M 0.785, 15M 1.570, 20M 2.355, 25M 3.925, 30M 5.495 and 35M 7.850 kg/m.
  • Rebar and structural steel are often priced per tonne or per pound; convert to a per kg or per lb price in CA$ before entering it.
  • Metric W-shape names carry the nominal mass, so a W310x39 weighs about 39 kg per metre.

Sources and further reading

  1. Compressive resistance tables for compression members (CSA S16), Canadian Institute of Steel Construction. HSS to CSA G40.21 Class C and Class H, with a worked example for HSS 203 x 203 x 6.4.
  2. Reinforcing bars (rebar), Russel Metals. CSA G30.18 bar designations with nominal area and mass: 10M 100 mm², 0.785 kg/m; 15M 200 mm², 1.570 kg/m.

Frequently asked questions

How much does 10M rebar weigh per metre?

0.785 kg/m, from its 100 mm² nominal area at 7,850 kg/m³. That is about 0.53 lb/ft. Enter a 11.284 mm round bar to get the same figure and the total for a bundle.

What diameter is 15M rebar?

Its nominal area is 200 mm², which is the area of a 15.96 mm round bar; the rounded 16 mm is often quoted. The deformations make the outside dimension larger, so use the area for weight.

Is W200x27 the same as W8x18?

Yes. Canadian practice names W-shapes by nominal depth in mm and mass in kg/m; W200x27 is the metric name of the W8x18. The calculator gives 26.2 kg/m from its plate dimensions without the fillets.

What is the difference between HSS Class C and Class H?

Under CSA G40.21, Class C hollow sections are cold-formed and Class H are hot-formed or stress-relieved. Class H has tighter corners, so it weighs slightly more for the same size, and CSA S16 gives it a higher column curve.

How do I price a steel order in Canadian dollars?

Pick C$ in the currency box and enter the supplier's price per kg (or per lb in imperial mode). The cost is the total weight times that price.

Is there an in-depth guide to the Steel Weight Calculator?

Yes. “Steel Weight Formulas for Plate, Bar, Pipe and Sections (kg/m and lb/ft)” covers the background, how it works, common pitfalls and worked examples. Read the full guide.