Pakistan version. Metric with force in tonnes, taking shear strength as 0.8 of the 550 N/mm² upper tensile limit of PS 4798 structural steel, with SWG sheet examples. US version
Punching Force Calculator (Tonnes, MS Plate and Sheet)
Tonnes and kN to punch a hole or slot in MS plate or SWG sheet from cut perimeter, thickness and shear strength estimated from PS 4798 tensile strength.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Punching Force Calculator?
This version opens on an 18 mm hole in 8 mm structural plate. PS 4798, Pakistan's carbon structural steel standard, allows a tensile strength anywhere from 400 to 550 N/mm². Taking shear strength as 0.8 of the upper figure gives 440 N/mm², and the punch needs 199.1 kN, or 20.3 tonnes. Plate at the 400 N/mm² minimum (320 N/mm² in shear) needs 14.8 tonnes for the same hole.
The 0.8 ratio is a rule of thumb for steels, not part of the standard; the calculator lets you change it. With a mill test certificate, enter its tensile strength, and the force follows in proportion. Without one, the upper limit keeps the press from stalling on a hard batch.
For sheet, use the mild steel preset of 345 N/mm². Six 25 x 12 mm slots punched in one stroke in 22 SWG (0.711 mm) sheet need 93.8 kN, about 9.6 tonnes.
- Round, square, rectangular, oblong and custom perimeters
- Shear strength presets, custom value or estimate from tensile strength
- kN, US tons, metric tonnes and lbf
- Multiple holes in one stroke and material comparison table
- Minimum hole size warning for slender punches
Updated
How to use the Punching Force Calculator
- Choose metric or inch units and the hole shape.
- Enter the hole dimensions: diameter, side, length and width, slot length and width, or the full cut perimeter for a custom shape.
- Enter the sheet thickness and the number of holes punched in the same stroke.
- Pick a material shear strength, type your own, or estimate it from tensile strength.
- Read the force per hole and in total, and compare materials in the table below.
Worked examples
18 mm hole in 8 mm PS 4798 plate
Input
Round 18 mm, t 8 mm, tensile 550 N/mm² x 0.8 = 440 N/mm² shear
Output
199.1 kN, 20.3 t (perimeter 56.55 mm); at 400 N/mm² tensile, 144.8 kN, 14.8 t
The hole is more than twice the thickness, so the punch is not at risk of buckling. A 20 tonne press would be overloaded by hard plate.
22 mm hole in 10 mm plate
Input
Round 22 mm, t 10 mm, 440 then 320 N/mm² shear
Output
304.1 kN, 31.0 t at 440; 221.2 kN, 22.6 t at 320
Thicker plate and a bigger hole both raise the force: the cut edge is 69.1 mm long and 10 mm deep.
Six slots in 22 SWG sheet
Input
Oblong 25 x 12 mm, t 0.711 mm (22 SWG), mild steel 345 N/mm², 6 per stroke
Output
93.8 kN for all six, 9.56 t
Each slot needs about 1.6 tonnes; punching them together multiplies the force by six.
50 mm square cut-out in 1 mm sheet
Input
Square 50 mm, t 1.0 mm, mild steel 345 N/mm²
Output
69.0 kN, 7.04 t
A long cut edge in thin sheet can need as much force as a small hole in plate: here the edge is 200 mm long.
Background and insight
The shear strength values are the typical figures used in punching charts: 50 ksi (345 MPa, or 25 tons per square inch) for mild steel, about 75 ksi (517 MPa) for annealed 304 stainless, 20 ksi for 5052-H32 and 30 ksi for 6061-T6 aluminium from Aluminum Association data, and around 35 ksi for half-hard brass. When only the tensile strength is known, shear strength is often taken as about 0.8 times it for steels, the default ratio here.
The old ironworker shortcut, tons = diameter x thickness x 80 for mild steel in inches, is the same formula with π x 50 ksi / 2,000 lb per ton = 78.5 rounded up. Some charts use 30 tons per square inch rather than 25 to include an allowance for friction and dull tooling. Either way, the force is proportional to perimeter, so a 2 in hole needs twice the force of a 1 in hole, not four times.
The formula is for sharp tools at proper clearance, typically 5 to 10% of thickness per side for mild steel. Worn punches and tight clearance push the force up; a shear angle ground on the punch face spreads the cut over part of the stroke and lowers the peak. Very small holes are limited by the punch itself: a punch thinner than the sheet tends to buckle or snap, which is why the common minimum is a hole at least as large as the thickness in mild steel and about twice the thickness in stainless.
Common use cases
Ironworker and punch press capacity
Check that a hole size and thickness are inside the machine’s punching tonnage.
Turret punch tooling
Estimate the force for a station before choosing standard or thick-turret tooling.
Blanking dies
Size the press for a blanking or piercing die from the total cut perimeter.
Hydraulic punch kits
See whether a portable hydraulic punch can make a given hole in field steel.
Tips and limitations
- The calculator warns when a round hole is smaller than the sheet thickness in mild steel (twice the thickness in stainless), where punches tend to break.
- Leave headroom between the calculated force and the press rating; the formula assumes sharp tooling and the strength you entered.
- Shear strength, not yield, sets the punching force; take it from the certificate where you can.
Sources and further reading
- PS 4798:2017 (Rev) Carbon Structural Steel, Pakistan Standards and Quality Control Authority (PSQCA). Based on ASTM A36/A36M-14; covers plates, shapes and bars. Table 2: tensile strength 400 to 550 MPa (58 to 80 ksi), minimum yield point 250 MPa (36 ksi).
- List of compulsory items to meet Pakistan Standards, Pakistan Standards and Quality Control Authority (PSQCA). Includes PS 4798 Structural Steel, PS-ISO 3573 Hot-Rolled Carbon Steel Sheet and PS-ISO 3574 Cold Reduced Carbon Steel Sheet of commercial and drawing qualities.
- Standard wire gauge, Wikipedia. Table of Imperial Standard Wire Gauge sizes 1 to 30 in inches and mm.
Frequently asked questions
How many tonnes does it take to punch an 18 mm hole in 8 mm plate?
About 20.3 tonnes for PS 4798 plate at its 550 N/mm² upper tensile limit (440 N/mm² in shear), or 14.8 tonnes at the 400 N/mm² minimum. Force = π x 18 x 8 x shear strength in N.
What shear strength should I use for PS 4798 plate?
PS 4798 states tensile strength, 400 to 550 N/mm², not shear strength. A common estimate for steel is 0.8 x tensile, which gives 320 to 440 N/mm².
What is the punching force formula in tonnes?
Cut perimeter (mm) x thickness (mm) x shear strength (N/mm²) gives newtons; divide by 9,807 for tonnes. For a round hole the perimeter is π x diameter.
How thick is 22 SWG sheet for punching?
0.711 mm. Six 25 x 12 mm slots in one stroke need about 9.6 tonnes at 345 N/mm².
Can I punch a hole smaller than the plate thickness?
The calculator flags a round hole narrower than the plate thickness in mild steel (twice the thickness in stainless), because the punch becomes slender and prone to breaking. Drill or laser-cut smaller holes instead.
Is there an in-depth guide to the Punching Force Calculator?
Yes. “Punching Force: Perimeter, Thickness and Shear Strength” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.