Australia version. Metric, with Australian section names (200UB25.4, SHS to AS/NZS 1163), N-class reinforcing bar, prices in A$ and notes on how merchant tables differ from the calculated mass. US version
Steel Weight Calculator (Australia)
Weight of Australian UB and UC sections, SHS and RHS to AS/NZS 1163, flat bar, plate and N-class reo in kg/m and per length, priced in A$ per kg.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Steel Weight Calculator?
Australian structural steel is named by its mass: a 200UB25.4 is a 200 mm universal beam weighing 25.4 kg per metre, made to AS/NZS 3679.1. For rolled sections the name is the answer, so this calculator earns its keep on the rest of a cut list: hollow sections, flats, plate, round and square bar, and reo.
Hollow sections are the case to watch. Australian SHS and RHS are cold-formed to AS/NZS 1163, and InfraBuild lists 100 x 100 x 5.0 SHS at 14.2 kg/m. The calculator's cold-formed corner option follows the European EN 10219 radii and gives 14.41 kg/m, about 1.5% heavier, because the corner geometry is not identical. For ordering, use the merchant table; for checking a delivery, a bundle or a crane lift, 1.5% is well inside the margin you would allow anyway.
Reinforcing bar is the other trap. N12 bar has a nominal mass of 0.888 kg/m from its 12 mm diameter, and that is what the calculator gives. Merchant price lists can be higher: InfraBuild's steel guide lists N12 at 0.93 kg/m and says its calculated mass includes an allowance for rolling variations. If you are paying by the tonne, ask which mass the invoice uses.
- Plate, flat, round, square and hex bar, round tube, SHS, RHS, angle, channel and I-beam
- EN 10219 and EN 10210 corner radii for hollow sections, or sharp corners
- Weight per metre and per foot, per piece and in total, in kg and lb
- Density presets for carbon and stainless steel, cast iron, aluminium, copper, brass and titanium, all editable
- Comparison table for every material, surface area for coating, optional cost
Updated
How to use the Steel Weight Calculator
- Choose metric (mm, m, kg) or imperial (in, ft, lb). Switching converts the sizes you already entered.
- Pick the shape and enter its dimensions. Tubes need the outside size and the wall thickness.
- For square or rectangular tube, choose cold-formed, hot-finished or sharp corners.
- Enter the length of each piece and the quantity, then pick the material or type a density.
- Read the total, the weight of each piece, the weight per metre or foot and the surface area; add a price per kg or lb for a cost.
Worked examples
100 x 100 x 5.0 SHS, one 8 m length
Input
Square tube 100 x 5 mm, cold-formed corners, 8 m
Output
14.41 kg/m; 115.3 kg
At InfraBuild's 14.2 kg/m the same length is 113.6 kg. Either way two people should not carry it by hand; plan mechanical lifting.
100 bars of N12, 6 m
Input
Round bar 12 mm, 6 m, quantity 100
Output
0.888 kg/m; 532.7 kg nominal
At a listed 0.93 kg/m the same bundle is billed as 558 kg. The calculator shows the nominal figure the design and bar schedule use.
Background and insight
Weight is simply cross-section area times length times density. The area formulas are exact for the idealised shapes: a round tube is π(D − t)t, an angle is t(a + b − t), and a hollow section with rounded corners is 2t(B + H − 2t) − (4 − π)(ro² − ri²). The ASME B36.10 pipe weight formula, 10.69(D − t)t in lb/ft with inches, is the same equation with the steel density folded in.
Carbon steel is taken as 7,850 kg/m³ (0.2836 lb/in³), the value EN 10025 and most section tables use. Stainless grades are heavier: EN 10088-1 gives 7,900 kg/m³ for 1.4301 (304) and 8,000 kg/m³ for 1.4401 (316). Aluminium alloys are about 2,700 kg/m³, copper C11000 about 8,890 kg/m³ and cartridge brass about 8,530 kg/m³. All of these are typical values at room temperature; enter your supplier's figure if it differs.
Real stock is never exactly nominal. Mill tolerances on plate thickness and bar diameter (EN 10029, ASTM A6) allow a few percent either way, and rolled beams, channels and angles have root fillets that add a little area. Use the theoretical weight for estimating and quoting, and the certified weight on the delivery note for lifting plans.
Common use cases
Quoting fabrication jobs
Total the weight of plates, tubes and sections in a frame to price material and galvanising.
Lifting and transport
Check that a bundle of bar or a stack of plate is within a crane, forklift or trailer limit.
Comparing materials
See how much an aluminium or stainless version of the same part weighs before redesigning.
Estimating dead load
Get kg per metre of a beam or rail to add self-weight to a structural load calculation.
Tips and limitations
- Australian designations put the mass last: 310UC96.8 is a 310 mm universal column at 96.8 kg/m.
- Steel merchants quote per metre, per length or per tonne; divide a tonne price by 1,000 to enter A$ per kg.
- DuraGal and other galvanised hollow sections carry a zinc coating that adds a little mass; use the merchant figure where it matters.
- Common reo sizes are N10, N12, N16, N20, N24, N28, N32 and N36; enter the number as the diameter in millimetres.
Sources and further reading
- Know Your Steel (Edition 9, June 2023), InfraBuild Steel Centre. Page 11: 200UB (203 x 133) at 25.4 kg/m, meets AS/NZS 3679.1:2016. Page 28: 100 x 100 x 5.0 SHS at 14.2 kg/m, AS/NZS 1163:2016. Page 64: N12 at 0.93 kg/m; calculated mass includes an allowance for rolling manufacturing variations (AS/NZS 4671).
- AS/NZS 3679.1:2016 Structural steel, Part 1: Hot-rolled bars and sections, Standards Australia. Current standard for the production and supply of hot-rolled structural steel bars and sections.
- AS/NZS 1163:2016 Cold-formed structural steel hollow sections, Standards Australia. Current standard for cold-formed, electric resistance-welded structural steel hollow sections.
Frequently asked questions
How much does a 200UB25.4 weigh?
25.4 kg per metre, as the name says and as InfraBuild's section table lists it, so a 9 m length is 228.6 kg. If you enter the section as an I-beam from its plate dimensions, the calculator comes out a little lighter because it leaves out the root fillets, so use the designation mass for rolled sections.
What is the weight of N12 reo per metre?
The nominal mass is 0.888 kg/m (12 mm diameter at 7,850 kg/m³). Some merchants list a higher figure, such as 0.93 kg/m, that includes an allowance for rolling variation, so check which one your quote uses.
Why is my SHS weight different from the supplier's table?
Corner radii. Australian SHS to AS/NZS 1163 is listed at 14.2 kg/m for 100 x 100 x 5.0, while the calculator's cold-formed option uses European corner radii and gives 14.41 kg/m. Use the supplier figure for ordering.
How do I work out the price of steel per metre?
Multiply the kg per metre by the price per kg. A merchant price of A$2,500 per tonne is A$2.50 per kg, so 100 x 100 x 5.0 SHS at 14.2 kg/m is about A$35.50 per metre before cutting and delivery.
How heavy is a sheet of 10 mm plate?
7.85 kg per square metre per millimetre, so 78.5 kg/m². A 2,400 x 1,200 mm sheet of 10 mm plate is 226 kg; enter the size to check yours.
Is there an in-depth guide to the Steel Weight Calculator?
Yes. “Steel Weight Formulas for Plate, Bar, Pipe and Sections (kg/m and lb/ft)” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.