Australia version. Metric by default with Australian N-bar sizes from N12 to N36 (AS/NZS 4671), including N24 and N36, masses in kg/m and the price per bar in A$. US version
Reo Bar Calculator (N12 to N36)
Count N12, N16 or N20 reo bars for a slab, footing or raft with AS/NZS 4671 masses in kg per metre, laps in bar diameters and the stock lengths to order.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Rebar Calculator?
Australian reinforcement, or reo, is specified by class and diameter: N12 is a 12 mm Class N deformed bar to AS/NZS 4671 with a 500 MPa yield strength, and the N in a D500N bar means normal ductility. The nominal masses match the metric bar table: 0.888 kg/m for N12, 1.58 for N16, 2.47 for N20, 3.55 for N24, 4.83 for N28, 6.31 for N32 and 7.99 for N36, and this version includes the N24 and N36 sizes that other markets do not use.
Enter the footing, raft or slab size, the cover and the bar spacing each way, and the tool counts the bars, adds laps where a run is longer than the stock bar, and gives the length, kilograms and stock bars to buy. House slabs in Australia are mostly reinforced with mesh such as SL82 plus trench mesh in the beams, which this tool does not count; it is for the bar-reinforced parts and for checking a reo schedule.
- US bar sizes #3 to #11 with ASTM A615 weights and metric 8 to 32 mm bars
- Single or double mats, edge cover, hooks and lap splices
- Stock-length cutting estimate with offcut and lap count
- Steel area per foot or per metre of width for design checks
- Copy, share link and cost per stock bar; runs in your browser
Updated
How to use the Rebar Calculator
- Pick imperial or metric. Plan dimensions are in feet or metres; cover, spacing and laps are in inches or millimetres.
- Enter the slab or footing length and width and the edge cover. Add a hook or bend length per end if the bars turn up at the edges.
- Choose the bar size and the centre-to-centre spacing of the bars running along the length and along the width.
- Select a single mat or top and bottom mats, the stock length your supplier sells, and the lap length in bar diameters or as a length.
- Read the bar counts, total length, weight and stock bars to buy, then copy the takeoff or share a link with the inputs.
Worked examples
Garage pad, 8 x 5 m, N12 at 200 each way
Input
8 x 5 m, cover 40 mm, N12 @ 200 mm both ways, one layer, 6 m stock bars, lap length 500 mm (the NCC Housing Provisions minimum for bars up to 12 mm)
Output
65 bars, 407.3 m, 361.7 kg; 25 laps; 78 stock bars of 6 m
The 7.92 m bars are longer than a 6 m stock bar, so each is a 6 m bar plus a 2.42 m piece lapped 500 mm. Asking for 12 m stock bars removes the laps if the supplier carries them.
Raft, 10 x 10 m, N16 at 250, top and bottom
Input
10 x 10 m, cover 50 mm, N16 @ 250 mm both ways, two layers, 12 m stock bars
Output
160 bars, 1,584 m, 2,501.1 kg (2.5 t); 160 stock bars of 12 m
Each 9.9 m bar fits a 12 m stock bar with a 2.1 m offcut that cannot be paired, so offcuts are 336 m in total; a reo supplier cutting to a schedule wastes much less.
Background and insight
The bar count uses the fence-post rule: a clear width of W - 2c at spacing s holds floor((W - 2c) / s) + 1 bars, with a bar at each edge. Counting only (W - 2c) / s is the classic takeoff error that leaves you one bar short on every run. Bars along the length are spaced across the width, so the two directions swap dimensions.
When a bar run is longer than the stock length, it is made from n pieces that overlap by the lap length, so n pieces cover n x S - (n - 1) x lap and n = ceil((run - lap) / (S - lap)). The lap itself is a design value. ACI 318 sets tension lap splices at 1.0 or 1.3 times the development length, which depends on concrete strength, bar size, cover and position; 40 bar diameters is a common starting value on site drawings, not a code check. Cover also comes from the code: ACI 318 asks for 3 in where concrete is cast against and permanently exposed to earth, which is why footings use 3 in (75 mm).
Common use cases
Ordering steel for a slab on grade
Turn a spacing note such as "#4 @ 12 in EW" into a piece count and a weight that a supplier can quote.
Checking a fabricator quote
Compare the supplier's weight and bar list against an independent takeoff before the delivery arrives.
Footings and mat foundations
Add hooks at each end and a second mat to estimate a spread footing or raft.
Comparing bar size against spacing
Swap #4 at 12 in for #5 at 16 in and compare steel area per foot, weight and the number of bars to tie.
Tips and limitations
- Buy reo certified to AS/NZS 4671 and check the producer certificate; some products are heavier than the nominal mass per metre.
- Cover depends on exposure and the member: the structural engineer's drawings, under AS 3600 or AS 2870 for house slabs, set it.
- Protect the ends of starter bars with caps on site.
Sources and further reading
- Housing Provisions Part 4.2 Footings, slabs and associated elements, Australian Building Codes Board. Table 4.2.11b minimum laps: 500 mm for bars up to 12 mm, 700 mm over 12 mm up to 16 mm; 4.2.11(5) cover.
- AS/NZS 4671:2019 Steel for the reinforcement of concrete, Standards Australia. Classes, designations and nominal masses for reinforcing bar.
- Deformed reinforcing bar (rebar), Class N, InfraBuild. Australian producer data for N bars.
Frequently asked questions
How much does N12 reo weigh per metre?
0.888 kg per metre. N16 weighs 1.58 kg/m, N20 2.47, N24 3.55, N28 4.83, N32 6.31 and N36 7.99 kg/m, the AS/NZS 4671 nominal masses.
What does N12 mean in reinforcement?
A deformed (ribbed) bar of 12 mm nominal diameter in Class N, normal ductility, with a 500 MPa characteristic yield strength. It is written D500N12 in full. R bars are plain round bars, and L means low ductility, used in mesh.
How many N12 bars are in a tonne?
A 6 m N12 bar weighs 5.33 kg, so a tonne is about 188 bars; in 12 m lengths, about 94.
What lap length should I use for N12 bars?
For footings and slabs built to Part 4.2 of the ABCB Housing Provisions, Table 4.2.11b sets minimum laps of 500 mm for bars up to 12 mm diameter and 700 mm for bars over 12 mm up to 16 mm. An engineered slab follows the laps on its drawings, which under AS 3600 depend on concrete strength, cover, spacing and bar position. This version opens with a 500 mm lap; switch the lap to bar diameters if the drawings give it that way.
Should a house slab use reo bars or mesh?
Residential slabs on ground commonly use mesh such as SL82 or SL72, with trench mesh in the edge and internal beams as AS 2870 and the engineer specify. Bars appear in footings, rafts, suspended slabs and at re-entrant corners and openings.
Is there an in-depth guide to the Rebar Calculator?
Yes. “Rebar Takeoff for Slabs: Bar Counts, Laps, Cutting and Weight” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.