United Kingdom version. Set up for UK heating oil tanks: litres and millimetres, a dip chart to mark your stick, and the England storage rules that start above 3,500 litres at a home. US version
Oil Tank Volume Calculator (UK)
Turn a dipstick reading into litres of heating oil for rectangular and cylindrical tanks, check capacity against the 3,500 litre rule and size a 110% bund.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Tank Volume Calculator?
Homes off the gas grid in Britain buy heating oil by the litre and usually find out how much is left by dipping the tank. This version starts with a rectangular steel tank measured inside in millimetres. A tank 1,800 by 1,100 by 1,100 mm holds 2,178 litres when brim full, and a dip of 400 mm means 792 litres, enough to judge whether to order before a price change or a cold snap.
Cylindrical tanks lying on their side are where guessing goes wrong. In a tank 1,200 mm across and 2,000 mm long, a 300 mm dip is a quarter of the height but only 442 litres, or 19.6% of the 2,262 litre capacity. The dip chart panel prints the litres for every step of your stick, so you can mark it once and stop estimating.
Capacity also matters for the rules. The Control of Pollution (Oil Storage) (England) Regulations 2001 exclude tanks at private dwellings only up to 3,500 litres, so a bigger tank at a house must meet the storage rules, including a bund that holds 110% of the tank. Businesses are covered from 201 litres.
- Seven shapes: horizontal and vertical cylinder, rectangular, horizontal and vertical capsule, cone bottom and sphere
- Filled volume, percent full and ullage at any depth
- Depth for a target volume, solved numerically
- Dip chart table and volume-depth chart at any step
- Litres, m³, US and UK gallons, ft³ and oil barrels with exact conversions
Updated
How to use the Tank Volume Calculator
- Pick the tank shape: rectangular for a box-shaped steel tank, horizontal cylinder for a round tank lying on its side.
- Enter the inside dimensions in millimetres. For a plastic bunded tank use the maker's stated capacity and chart instead, because the inner tank is not a simple shape.
- Enter the dipstick reading as the liquid depth and read the litres, the percentage full and the space left for a delivery.
- Set the dip chart step to your stick's marks (say 50 mm) and print the table for the boiler house.
Worked examples
Rectangular steel tank, 400 mm on the dipstick
Input
Rectangular 1,800 x 1,100 x 1,100 mm, depth 400 mm
Output
792 litres in a 2,178 litre tank (36.4% full)
In a box-shaped tank litres rise in a straight line with depth, so each 100 mm of dip is 198 litres here. The space above the oil, 1,386 litres, is the most a delivery could add before the tank is brim full; order less to leave room.
Horizontal cylinder, 300 mm on the dipstick
Input
Horizontal cylinder 1,200 mm diameter x 2,000 mm long, depth 300 mm
Output
442 litres of 2,262 (19.6%); at 600 mm, 1,131 litres (50%)
A quarter of the height holds less than a fifth of the volume because the tank is narrow near the bottom. Only at exactly half the diameter does the dip match the percentage.
Is a larger domestic tank over the 3,500 litre limit?
Input
Horizontal cylinder 1,400 mm diameter x 2,300 mm long
Output
3,541 litres capacity; 500 litres left at a dip of about 278 mm
At 3,541 litres this tank is above the 3,500 litre exclusion for private dwellings in England, so the oil storage regulations apply to it. Use the stated nominal capacity on the tank plate if it differs from your measurement.
Loft cold water cistern
Input
Rectangular 610 x 430 x 460 mm, water at 380 mm
Output
120.7 litres brim full (26.5 UK gallons); 99.7 litres at the working level
Cisterns are often described in imperial gallons. Choose UK gal as the volume unit to compare with the size printed on an old cistern.
Background and insight
A horizontal cylinder's partial volume is the area of a circular segment times the length: A = r² cos⁻¹((r − h)/r) − (r − h)√(2rh − h²). The same segment geometry, rotated, gives the spherical cap V = πh²(3r − h)/3 used for spheres and for the hemispherical ends of capsule tanks. A cone bottom fills as a smaller cone until the liquid reaches the cylinder.
Because the segment area is not linear in depth, rules of thumb mislead. At a quarter of the diameter a horizontal cylinder is 19.6% full, at half it is exactly 50% and at three quarters it is 80.4%. A sphere at a quarter of its height is only 15.6% full.
Unit factors are exact: 1 US gallon is 3.785411784 L, 1 imperial gallon 4.54609 L, and an oil barrel 42 US gallons (158.987 L). For custody transfer and tax purposes, tanks are calibrated by recognised strapping methods such as API MPMS Chapter 2 rather than from nominal drawings, because real tanks have dished heads, slopes, dents and internal fittings.
Common use cases
Fuel and oil inventory
Turn a dipstick reading into litres or gallons for heating oil, diesel or lube tanks.
Water storage and rainwater tanks
Find capacity and remaining days of supply from the water level.
Level gauge marking
Get the depth for 25%, 50% or any volume to mark a sight glass or set level switches.
Process vessels and hoppers
Volume in capsule and cone-bottom vessels at any fill, for batching and dosing.
Tips and limitations
- Measure inside dimensions. Steel tank walls are thin, but a measurement over flanges or the outside of a plastic tank overstates the capacity.
- Dip the tank at the same point each time, ideally the middle, because a tank that leans a little reads differently at each end.
- A bund must hold 110% of the tank's capacity where the regulations apply, so use the total capacity figure, not the oil in the tank, when checking one.
- If the tank is inside a building, building regulations may require extra fire protection; ask your council's building control.
Sources and further reading
- Oil storage regulations for businesses, GOV.UK. Rules apply to containers of 3,501 litres or more at a home and 201 litres or more elsewhere; bunds must hold 110% of the container.
- The Control of Pollution (Oil Storage) (England) Regulations 2001, regulation 2, legislation.gov.uk. Exclusions: containers of 200 litres or less, and private dwellings with containers of 3,500 litres or less.
- Circular Segment, Wolfram MathWorld. The formula behind the volume of a horizontal cylinder at any depth.
Frequently asked questions
How do I work out how much heating oil is left in my tank?
Measure the depth of oil with a dipstick, enter the tank's inside dimensions and its shape, and the calculator gives the litres at that depth. For a rectangular tank it is simply length x width x depth; for a cylinder on its side it uses the circular segment, so the litres are not proportional to depth.
Do the oil storage regulations apply to my home oil tank?
In England the Control of Pollution (Oil Storage) Regulations 2001 do not apply to a private dwelling's tank of 3,500 litres or less. A larger tank at a home, and any tank over 200 litres at a business, school or other premises, must meet them. Wales, Scotland and Northern Ireland have their own regulations.
How big does a bund have to be?
Where the rules apply, a bund must hold 110% of the capacity of the container it protects. For a 2,500 litre tank that is 2,750 litres. An integrally bunded tank has the bund built in, so you mainly need the figure when checking a separate masonry or steel bund.
How many litres is a 1,000 gallon tank?
An imperial gallon is 4.546 litres, so 1,000 UK gallons is 4,546 litres. If an older UK tank or cistern is marked in gallons, they are imperial gallons, not US ones; pick UK gal in the volume unit.
Can I use this for a plastic bunded oil tank?
Only roughly. The inner tank of a bunded plastic tank has rounded corners, ribs and a sloping base, so measuring the outside overstates the volume. Use the maker's capacity and contents chart, or a remote gauge set up for that model.
Is there an in-depth guide to the Tank Volume Calculator?
Yes. “Tank Volume Formulas and Dip Charts for Horizontal, Vertical and Odd Shapes” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.