India version. Metric with force in tonnes, worked for MS plate and SWG GI sheet, with the power press examination rules of the Model Rules framed under the Factories Act. US version
Punching Force Calculator (Tonnes, MS and GI Sheet)
Tonnes and kN to punch a hole or slot in MS, GI or stainless sheet from the cut perimeter and thickness in mm or SWG, for power press tools and hydraulic punches.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Punching Force Calculator?
Press tool makers and fabricators in India size a power press by tonnage, so this version opens on a common job: an 18 mm hole in 6 mm MS plate. The cut edge is 56.5 mm long, and at the usual 345 N/mm² shear strength for mild steel it takes 117.1 kN, about 11.9 tonnes.
For sheet, the thickness usually comes as a gauge. 22 SWG GI is 0.711 mm, and four 20 x 10 mm slots punched together in it need about 5.1 tonnes. For heavier or named grades use the tensile strength from the test certificate and the "Estimate from tensile strength" option.
Size the press with a margin for blunt punches, then remember the machine itself: Schedule VI of the Model Rules framed under the Factories Act, 1948 covers power presses and calls for a thorough examination by a competent person at least every 12 months. The Occupational Safety, Health and Working Conditions Code, 2020 repeals the Factories Act from the date the Central Government notifies, and keeps rules made under the old Act in force, where they do not conflict with the Code, until they are repealed. Ask your state's Inspector of Factories which power press rules apply to your works.
- Round, square, rectangular, oblong and custom perimeters
- Shear strength presets, custom value or estimate from tensile strength
- kN, US tons, metric tonnes and lbf
- Multiple holes in one stroke and material comparison table
- Minimum hole size warning for slender punches
Updated
How to use the Punching Force Calculator
- Choose metric or inch units and the hole shape.
- Enter the hole dimensions: diameter, side, length and width, slot length and width, or the full cut perimeter for a custom shape.
- Enter the sheet thickness and the number of holes punched in the same stroke.
- Pick a material shear strength, type your own, or estimate it from tensile strength.
- Read the force per hole and in total, and compare materials in the table below.
Worked examples
18 mm hole in 6 mm MS plate
Input
Round 18 mm, t 6 mm, mild steel 345 N/mm²
Output
117.1 kN, 11.94 t
The hole is three times the thickness, so the punch is sturdy. A 15 tonne press leaves only about 25% margin, which blunt tooling can use up.
Four slots in 22 SWG GI
Input
Oblong 20 x 10 mm, t 0.711 mm (22 SWG), mild steel 345 N/mm², 4 per stroke
Output
50.46 kN for all four (5.15 t), 12.62 kN each
Typical of cable tray or panel work. The zinc coating is too thin to change the force.
50 mm square cut-out in 2 mm sheet
Input
Square 50 mm, t 2 mm, 345 N/mm²
Output
138 kN, 14.07 t
A large perimeter in thin sheet can need more force than a small hole in thick plate. The cut edge here is 200 mm long.
14 mm hole in 3 mm plate from the certificate
Input
Round 14 mm, t 3 mm, UTS 410 N/mm² x 0.8
Output
43.28 kN, 4.41 t
Using 0.8 of a 410 N/mm² tensile strength gives 328 N/mm² in shear, slightly below the 345 N/mm² chart value.
Background and insight
The shear strength values are the typical figures used in punching charts: 50 ksi (345 MPa, or 25 tons per square inch) for mild steel, about 75 ksi (517 MPa) for annealed 304 stainless, 20 ksi for 5052-H32 and 30 ksi for 6061-T6 aluminium from Aluminum Association data, and around 35 ksi for half-hard brass. When only the tensile strength is known, shear strength is often taken as about 0.8 times it for steels, the default ratio here.
The old ironworker shortcut, tons = diameter x thickness x 80 for mild steel in inches, is the same formula with π x 50 ksi / 2,000 lb per ton = 78.5 rounded up. Some charts use 30 tons per square inch rather than 25 to include an allowance for friction and dull tooling. Either way, the force is proportional to perimeter, so a 2 in hole needs twice the force of a 1 in hole, not four times.
The formula is for sharp tools at proper clearance, typically 5 to 10% of thickness per side for mild steel. Worn punches and tight clearance push the force up; a shear angle ground on the punch face spreads the cut over part of the stroke and lowers the peak. Very small holes are limited by the punch itself: a punch thinner than the sheet tends to buckle or snap, which is why the common minimum is a hole at least as large as the thickness in mild steel and about twice the thickness in stainless.
Common use cases
Ironworker and punch press capacity
Check that a hole size and thickness are inside the machine’s punching tonnage.
Turret punch tooling
Estimate the force for a station before choosing standard or thick-turret tooling.
Blanking dies
Size the press for a blanking or piercing die from the total cut perimeter.
Hydraulic punch kits
See whether a portable hydraulic punch can make a given hole in field steel.
Tips and limitations
- As a common rule of thumb, hole diameter should be at least the sheet thickness in MS and about twice the thickness in stainless; smaller holes break punches.
- Allow at least 20% over the calculated tonnage for wear and variation in the sheet.
- Schedule VI of the Model Rules lets only persons appointed by the occupier may set, adjust or try out the tools on a power press.
- State factory rules can differ from the Model Rules, and the OSH Code, 2020 changes the legal basis; the Inspector of Factories for your area can confirm what applies.
Sources and further reading
- Model Rules under the Factories Act, 1948, DGFASLI, Ministry of Labour and Employment. Schedule VI, Power Press: examination, testing and appointed tool setters.
- The Occupational Safety, Health and Working Conditions Code, 2020 (Gazette of India), DGFASLI, Ministry of Labour and Employment. Section 1(2) commencement by notification; section 143 repeals the Factories Act, 1948 and keeps rules made under it in force, where not contrary to the Code, until repealed.
- Galvanised steel, JSW Steel. GI sheet thickness range and coatings.
- ASM Handbook Volume 14B: Metalworking: Sheet Forming, ASM International. Piercing and blanking force.
Frequently asked questions
How many tonnes to punch an 18 mm hole in 6 mm MS plate?
About 11.9 tonnes (117.1 kN) at a shear strength of 345 N/mm². Force = π x 18 x 6 x 345 N.
What is the punching force formula in tonnes?
Cut perimeter (mm) x thickness (mm) x shear strength (N/mm²) gives newtons; divide by 9,807 for tonnes. For a round hole, perimeter = π x diameter.
What thickness is 22 gauge GI sheet for punching?
0.711 mm in SWG. Punching four 20 x 10 mm slots at once in it needs about 5.1 tonnes.
What inspection does a power press need in India?
Schedule VI of the Model Rules framed under the Factories Act says a power press may not be used unless a competent person has thoroughly examined and tested it within the previous 12 months. The OSH Code, 2020 repeals the Factories Act from its notified date but keeps existing rules in force, where they do not conflict, until they are repealed, so ask your state's Inspector of Factories which rules apply.
What shear strength should I take for MS?
345 N/mm² is the usual chart value. If you know the tensile strength from the test certificate, take about 0.8 of it.
Is there an in-depth guide to the Punching Force Calculator?
Yes. “Punching Force: Perimeter, Thickness and Shear Strength” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.