New Zealand version. Metric for New Zealand decks: boards bought by the metre length, joists at 400 or 450 mm on bearers and piles, H3.2 timber, and the barrier and consent rules that apply. US version

Decking Calculator (New Zealand)

Decking boards, joists, bearers, piles and screws for a NZ deck in metres, with the 1 m barrier rule, the 1.5 m consent exemption and H3.2 treated pine.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Deck Calculator?

This version uses the New Zealand names for the parts of a timber deck: boards on joists, joists on bearers and bearers on piles. The NZ Timber Preservation Council lists H3.2 for decking boards and for the joists and bearers of decks, and H5 for house piles. This version works in metres and millimetres and opens with a 4.8 x 3.0 m deck off the living room, fixed to the house with a ledger.

In 140 mm boards with 5 mm gaps that deck takes 21 rows and 24 boards bought in 4.8 m lengths, with 12 joists at 450 mm centres and about 500 screws. In 90 mm boards it takes 36 boards and 768 screws, because every extra row means two more screws at every joist. Board length matters as much as width: on a 6.0 m deck, 6.0 m boards need 28 lengths where 4.8 m boards need 55.

Two height rules shape the design. Building Code clause F4 needs a barrier wherever people could fall 1 metre or more, and the baluster spacing calculator covers its 100 mm gap rule. Separately, exemption 24 of Schedule 1 to the Building Act lets you build a deck without building consent as long as it is not possible to fall more than 1.5 metres from it.

  • Rows and boards by stock length, with nesting of short rows
  • Straight or diagonal decking and adjustable waste
  • Joists, rim, ledger, beam plies, posts and hangers
  • Face screws or hidden clips per crossing, with boxes and rate per area
  • Cut list, joist span readout, decking cost, metric and imperial
Read the guide: Estimating a Deck: Boards, Joists, Screws and Span Tables

Updated

How to use the Deck Calculator

  1. Choose imperial or metric and enter the deck length along the house and the projection out from it.
  2. Enter the actual board width, the gap between boards and the board length you will buy, then choose straight or diagonal boards.
  3. Set the joist spacing, joist size label and stock length, the rim thickness, and whether a ledger attaches the deck to the house.
  4. Enter the beams, plies, posts and the joist cantilever past the beam from your design or permit drawing.
  5. Choose face screws or hidden clips, the count per box and the waste, then read the materials and cut list.

Worked examples

4.8 x 3.0 m deck in 140 mm boards

Input

140 mm boards, 5 mm gaps, 4.8 m lengths, joists at 450 mm in 3.0 m lengths, ledger at the house, one bearer on four piles, 300 mm overhang past the bearer, 10% extra

Output

21 rows, 24 boards (100.8 m net); 12 joists at 2955 mm; 504 screws (about 35 per m², 2 boxes of 500); joist span 2.7 m from ledger to bearer

Joist, bearer and pile sizes come from the deck design or the span tables you are working to, for the timber grade and the span; the calculator counts the pieces once the sizes are chosen.

The same deck in 90 mm boards

Input

90 mm boards, everything else the same

Output

32 rows, 36 boards (153.6 m net); 768 screws (about 53 per m²)

Narrow boards add 11 rows and 264 screws over the same 14.4 m², which is more fixing time as well as more fixings.

6.0 x 3.6 m deck: 4.8 m or 6.0 m boards

Input

140 mm boards, 5 mm gaps, joists at 450 mm, boards bought in 4.8 m or 6.0 m lengths

Output

25 rows either way (150 m net); 55 boards in 4.8 m lengths or 28 in 6.0 m lengths; 15 joists at 3555 mm

A 6.0 m deck cannot be covered by one 4.8 m board per row, so each row needs two lengths and leaves an offcut. Buying boards that match the deck length halves the count and removes the end joins.

Background and insight

Joists are counted like studs: ceil(length / spacing) + 1 including both end joists. Rows of decking are ceil(projection / (board width + gap)), using the actual width. A 5/4x6 board is 5-1/2 in wide, so with a 3/16 in gap each row covers 5-11/16 in. When the deck is shorter than the boards, rows nest two or more to a board; when it is longer, butt joints have to land on joists and each row takes more than one board. Two face screws per board at every joist is the standard pattern, a little over 3 screws per square foot for 5-1/2 in boards at 16 in, and hidden clips use one per crossing.

Joist sizes and spans are a code question. In the US, IRC Section R507 holds the deck joist and deck beam span tables, which depend on species, grade, spacing and cantilever, and the American Wood Council publishes the same rules as DCA 6. Composite decking makers often require 12 in joist spacing for diagonal boards. The calculator shows your joist span so you can compare it with the table, but it does not size members.

Common use cases

  • Pricing a deck before a permit

    Get board, joist and fastener counts to compare composite and timber quotes.

  • Planning a resurface

    Count new boards and screws for existing framing by entering the deck size and joist spacing.

  • Choosing board direction

    Compare straight and diagonal layouts for board count, waste and fasteners.

  • Ordering stock lengths

    Try 12, 16 and 20 ft boards to find the length that nests best with your deck size.

Tips and limitations

  • Ask for H3.2 timber for decking, joists and bearers, and H5 for piles, and check the WOODmark stamp and hazard class on the timber.
  • Measure the fall at the outside edge of the deck. From 1 metre clause F4 needs a barrier, and above 1.5 metres the deck is outside the consent exemption.
  • Buy boards in the length that matches the deck where you can: on a 6.0 m deck, 6.0 m lengths need half as many boards as 4.8 m lengths and leave no end joins.

Sources and further reading

  1. Know your stuff: Exempt Building Work, Part 1, Licensed Building Practitioners (MBIE). Exemption 24: decks, platforms and boardwalks without consent where the fall is no more than 1.5 metres; barrier at 1 metre.
  2. Acceptable Solution F4/AS1: resource detail, Building CodeHub (MBIE). Clause F4 requires barriers where people could fall 1 metre or more.
  3. Choosing the Right Timber: timber hazard classes explained, NZ Timber Preservation Council. H3.2 for decking, joists and bearers; H4 for ground contact; H5 for house piles.

Frequently asked questions

Do I need building consent for a deck in NZ?

Not if it is not possible to fall more than 1.5 metres from the deck. That is exemption 24 in Schedule 1 of the Building Act, as the LBP Codewords series explains. A deck with a bigger possible fall is outside that exemption.

How does the calculator count bearers and piles?

Bearers are the beams that carry the joists and piles are the posts under the bearers. Enter how many bearers run under the deck, the plies in each and the piles per bearer, and the calculator lists them with the joists; their sizes and spacing come from the deck design or the span tables you are working to.

What treatment do decking boards need?

The NZ Timber Preservation Council lists H3.2 for decking, palings, handrails and the joists and bearers of decks and walkways, H4 for ground contact such as fence posts, and H5 for house piles and poles.

How many decking boards do I need for a 4.8 x 3.0 m deck?

In 140 mm boards with 5 mm gaps the 3.0 m width takes 21 rows. With boards bought in 4.8 m lengths each row is one board, so 21 plus 10% gives 24. In 90 mm boards it is 32 rows and 36 boards.

Should joists be at 400 or 450 mm centres?

The board size and species decide the maximum joist spacing, so follow the deck design or the board supplier. Closer joists add one or two joists and more screws: the 4.8 m deck goes from 12 joists and 504 screws at 450 mm to 13 joists and 546 screws at 400 mm.

How many screws per square metre of decking?

With two screws at each joist and joists at 450 mm, 140 mm boards take about 35 screws per m² and 90 mm boards about 53. The calculator counts every board and joist crossing for your deck size.

Is there an in-depth guide to the Deck Calculator?

Yes. “Estimating a Deck: Boards, Joists, Screws and Span Tables” covers the background, how it works, common pitfalls and worked examples. Read the full guide.