Canada version. Inches or millimetres, checked against the National Building Code of Canada for private stairs: rise 125 to 200 mm, run 255 to 355 mm, headroom 1,950 mm. US version
Stair Calculator (Canada)
Risers, treads, run and stringer length from the floor-to-floor height in inches or mm, checked against National Building Code private-stair rise and run limits.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Stair Calculator?
Stairs in Canadian houses follow Section 9.8 of the National Building Code, adopted with changes by each province. For a private stair serving a single dwelling, the rise must be between 125 and 200 mm and the run between 255 and 355 mm, with clear height over the stair of at least 1,950 mm and a width of at least 860 mm.
The run minimum is where US plans catch people out. A 10 in tread is fine under the US IRC, but 10 in is 254 mm, 1 mm under the Canadian minimum. A 105 in rise built as 14 risers of 7.5 in on 10 in treads therefore fails the NBC run check, while 10 1/4 in treads pass.
Enter the total rise and your target riser in inches or millimetres. The tool sets the riser count, checks rise and run against the NBC, and gives the total run and stringer length for cutting.
- Risers, treads, total run, stringer length and angle from the total rise
- Checks against IRC R311.7 riser, tread and nosing limits, plus 2R + T comfort
- Fit-to-run mode for stairs in a fixed space
- Scale side-view drawing and one-more, one-fewer riser comparison
- Inches or millimetres; copy the layout or share a link
Updated
How to use the Stair Calculator
- Measure finished floor to finished floor, allowing for flooring still to go down.
- Choose "National Building Code of Canada, private stair" under "Check against".
- Set the maximum riser, at most 7 7/8 in (200 mm), and the tread run.
- If the run fails, lengthen the tread or add a riser and check the room at the bottom.
Worked examples
A US-sized tread that fails the NBC
Input
Total rise 105 in, maximum riser 7.75 in, tread 10 in
Output
14 risers of 7.5 in (190.5 mm), 13 treads of 10 in (254 mm); total run 130 in
The rise passes, the run is 1 mm under the NBC minimum of 255 mm. With 10.25 in treads the run is 260 mm and the total run grows to 133.25 in.
Basement stair with an 8 in riser
Input
Total rise 96 in, maximum riser 8 in, tread 10.5 in
Output
12 risers of 8 in (203.2 mm); fails the 200 mm maximum
Use a 7 7/8 in maximum instead: 13 risers of 7.385 in (187.6 mm). Then make the treads at least 10 1/16 in, since 10 in is short.
Deck stairs
Input
Total rise 36 in, maximum riser 7.5 in, tread 11 in
Output
5 risers of 7.2 in (182.9 mm), 4 treads of 11 in; run 44 in; angle 33.2°
Exterior stairs serving a single dwelling are private stairs too, so the same limits apply.
Background and insight
The code numbers come from IRC section R311.7: R311.7.5.1 limits riser height to 7 3/4 inches (196 mm), R311.7.5.2 sets a 10 inch (254 mm) minimum tread, R311.7.2 requires 6 feet 8 inches of headroom measured from the sloped line of the nosings, and riser heights within a flight may differ by no more than 3/8 inch. Commercial stairs under the IBC are stricter, at a 7 inch maximum riser and 11 inch minimum tread, and local amendments are common, so confirm with your building department.
The 2R + T rule goes back to François Blondel, a 17th-century French architect who tied step size to the length of a natural stride; modern practice puts the target at 24 to 25 inches (610 to 635 mm). A 7 inch riser with an 11 inch tread scores 25, a classic comfortable stair. Steeper stairs save floor space but feel abrupt going down, which is when most stair falls happen.
Common use cases
Deck and porch stairs
Lay out stringers for the drop from a deck to grade, with the riser count and cut dimensions.
Basement and loft stairs
Check whether a replacement stair will fit the existing opening and pass inspection.
Planning a renovation
See how much floor space a new stair needs before moving walls.
Checking an existing stair
Measure a stair that feels steep and see which rule it breaks.
Tips and limitations
- Risers in a flight may vary by at most 5 mm between adjacent steps and 10 mm overall (NBC 9.8.4.4).
- Tread depth may exceed the run by up to 25 mm, so a nosing is allowed but not required.
- A single flight may not rise more than 3.7 m (NBC 9.8.3.3).
Sources and further reading
- National Building Code of Canada 2025 (Division B, Part 9), National Research Council of Canada (Government of Canada Publications). Tables 9.8.4.1 (rise) and 9.8.4.2 (run); 9.8.2.1 width; 9.8.2.2 height over stairs.
- Codes Canada, National Research Council Canada
Frequently asked questions
What is the maximum stair rise in Canada?
Under the National Building Code, 200 mm (about 7 7/8 in) for private stairs serving a single dwelling and 180 mm for public stairs. The minimum rise is 125 mm for both.
What is the minimum tread run under the National Building Code?
For private stairs with rectangular treads, 255 mm (about 10 1/16 in), up to a maximum of 355 mm. Public stairs need at least 280 mm.
How much headroom does a basement stair need in Canada?
At least 1,950 mm clear height over stairs in a single dwelling, measured from a line through the nosings. Under beams and ducting over stairs in a house with a secondary suite, some codes allow 1,850 mm; check your province.
Does Ontario use the same stair rules as the National Building Code?
Provinces adopt the NBC with their own changes, and Ontario, Quebec, British Columbia and Alberta publish their own codes. Check the stair tables in your provincial code or with your municipal building department before you cut stringers.
How wide must a stair be in a house?
At least 860 mm for one stair between each floor level within a dwelling unit and for exterior stairs serving a single dwelling, under NBC 9.8.2.1.
Is there an in-depth guide to the Stair Calculator?
Yes. “Roof Pitch, Stair Layout, AC Sizing and Running Costs Explained” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.