United Kingdom version. Metric, with S275 entered by its BS EN 10025-2 tensile strength, SWG sheet in mm, and a note on which UK punching machines count as power presses. US version

Punching Force Calculator (UK, kN and tonnes)

Force in kN and tonnes to punch holes and slots in S275, S355 or SWG sheet, from the cut perimeter in mm, with how PUWER treats punching machines and turret presses.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Punching Force Calculator?

British structural and sheet work is mostly in S275 and S355 to BS EN 10025-2, and those grades are specified by tensile strength rather than shear strength. This version therefore opens on "Estimate from tensile strength": 410 N/mm² for S275 at 0.8 gives 328 N/mm² in shear, a little below the 345 N/mm² figure many punching charts use for generic mild steel.

With that setting a 22 mm hole for an M20 bolt in 4 mm S275 needs 90.7 kN, about 9.25 tonnes. The same hole in 8 mm plate needs twice that, because force rises with thickness and with the hole perimeter, not with its area.

Use the result to check an ironworker, a turret station or a press tool against its rating, and leave a margin: blunt punches, tight clearance and the higher end of the S275 tensile range all push the real force up.

  • Round, square, rectangular, oblong and custom perimeters
  • Shear strength presets, custom value or estimate from tensile strength
  • kN, US tons, metric tonnes and lbf
  • Multiple holes in one stroke and material comparison table
  • Minimum hole size warning for slender punches
Read the guide: Punching Force: Perimeter, Thickness and Shear Strength

Updated

How to use the Punching Force Calculator

  1. Choose metric or inch units and the hole shape.
  2. Enter the hole dimensions: diameter, side, length and width, slot length and width, or the full cut perimeter for a custom shape.
  3. Enter the sheet thickness and the number of holes punched in the same stroke.
  4. Pick a material shear strength, type your own, or estimate it from tensile strength.
  5. Read the force per hole and in total, and compare materials in the table below.

Worked examples

22 mm bolt hole in 4 mm S275

Input

Round 22 mm, t 4 mm, UTS 410 N/mm² x 0.8 = 328 N/mm² shear

Output

90.68 kN, 9.25 t (10.19 US tons)

With the 345 N/mm² chart value for mild steel instead, the answer is 95.38 kN. The certificate tensile strength gives the better estimate for a named grade.

18 mm hole in 8 mm S275 plate

Input

Round 18 mm, t 8 mm, UTS 410 N/mm² x 0.8

Output

148.4 kN, 15.13 t

Typical of a cleat or base plate on an ironworker. The hole diameter is more than twice the thickness, so the punch is not at risk of buckling.

Ten 8.5 mm holes in 16 SWG mild steel

Input

Round 8.5 mm, t 1.626 mm (16 SWG), mild steel 345 N/mm², 10 holes per stroke

Output

149.8 kN for all ten (15.27 t), 14.98 kN each

A multi-punch tool that fires all ten together needs a press of at least 15 tonnes plus a margin. Stepping the punch lengths so half cut first halves the peak.

Background and insight

The shear strength values are the typical figures used in punching charts: 50 ksi (345 MPa, or 25 tons per square inch) for mild steel, about 75 ksi (517 MPa) for annealed 304 stainless, 20 ksi for 5052-H32 and 30 ksi for 6061-T6 aluminium from Aluminum Association data, and around 35 ksi for half-hard brass. When only the tensile strength is known, shear strength is often taken as about 0.8 times it for steels, the default ratio here.

The old ironworker shortcut, tons = diameter x thickness x 80 for mild steel in inches, is the same formula with π x 50 ksi / 2,000 lb per ton = 78.5 rounded up. Some charts use 30 tons per square inch rather than 25 to include an allowance for friction and dull tooling. Either way, the force is proportional to perimeter, so a 2 in hole needs twice the force of a 1 in hole, not four times.

The formula is for sharp tools at proper clearance, typically 5 to 10% of thickness per side for mild steel. Worn punches and tight clearance push the force up; a shear angle ground on the punch face spreads the cut over part of the stroke and lowers the peak. Very small holes are limited by the punch itself: a punch thinner than the sheet tends to buckle or snap, which is why the common minimum is a hole at least as large as the thickness in mild steel and about twice the thickness in stainless.

Common use cases

  • Ironworker and punch press capacity

    Check that a hole size and thickness are inside the machine’s punching tonnage.

  • Turret punch tooling

    Estimate the force for a station before choosing standard or thick-turret tooling.

  • Blanking dies

    Size the press for a blanking or piercing die from the total cut perimeter.

  • Hydraulic punch kits

    See whether a portable hydraulic punch can make a given hole in field steel.

Tips and limitations

  • Turret punch presses, ironworkers (combination punching and shearing machines) and guillotines are listed in Schedule 2 of PUWER, so the power press examination rules do not apply to them. The general PUWER duties on guarding and training still do.
  • A mechanical press with a flywheel and clutch running a piercing or blanking tool is a power press: guards are thoroughly examined every 6 or 12 months and inspected by an appointed person each shift.
  • Leave at least 20% over the calculated force for wear and material variation, and more for S355.
  • Order S275 and S355 by tensile strength on the certificate. Shear strength is rarely given, so the 0.8 ratio is the usual bridge.

Sources and further reading

  1. Safe use of power presses (L112), Health and Safety Executive. Power press definition and the PUWER Schedule 2 exclusions, including turret punch presses.
  2. Steel material properties, Steel Construction Institute. Minimum tensile strengths for S275 and S355.
  3. ASM Handbook Volume 14B: Metalworking: Sheet Forming, ASM International. Piercing and blanking force.

Frequently asked questions

What shear strength should I use for S275?

Estimate it from the tensile strength: 0.8 x 410 N/mm² gives about 328 N/mm² at the BS EN 10025-2 minimum. If the certificate shows a higher tensile strength, use that, since delivered plate is often above the minimum.

How much force to punch a 22 mm hole in 4 mm steel?

About 90.7 kN (9.25 tonnes) in S275 at its minimum tensile strength, or 95.4 kN with the 345 N/mm² chart value for mild steel.

Is a turret punch press a power press under PUWER?

No. Schedule 2 of PUWER lists combination punching and shearing machines, turret punch presses and similar machines for punching, shearing or cropping among the machines the power press regulations do not apply to.

How thick is 16 SWG for punching?

1.626 mm. If a drawing says "16 gauge" and comes from a US source, it may mean 1.519 mm, which needs about 7% less force.

How do I convert kN to tonnes for my press?

Divide by 9.807. A 90.7 kN hole is about 9.25 tonnes, so a 10 tonne station would be at its limit before any allowance for wear.

Is there an in-depth guide to the Punching Force Calculator?

Yes. “Punching Force: Perimeter, Thickness and Shear Strength” covers the background, how it works, common pitfalls and worked examples. Read the full guide.