United Kingdom version. Metric by default with a 2500 x 1250 mm sheet, plus the British Standard Wire Gauge (SWG) that UK trade still quotes, alongside the US gauge tables. US version

Sheet Metal Weight Calculator (UK, mm and SWG)

Weigh steel, stainless and aluminium sheet in kg from size in mm and thickness or British SWG gauge, such as a 2500 x 1250 sheet, with holes and cut-outs taken off.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Sheet Metal Weight Calculator?

UK stockholders sell sheet by the millimetre and invoice by the kilogram, so this version opens on a 2500 x 1250 x 2 mm mild steel sheet: 15.7 kg per square metre and 49.06 kg for the sheet. Change the size, thickness and material, add holes or cut-outs, and the weight per piece, the batch total and the kg/m² follow.

Older drawings, workshop habit and some suppliers still describe thickness as a gauge, and in Britain that means the Standard Wire Gauge (SWG), not the American sheet gauges most online charts show. "16 gauge" is 1.626 mm in SWG but 1.519 mm in the US Manufacturers' Standard Gauge, a 7% difference in weight. Switch the thickness to "Gauge number" and pick the SWG table so a British gauge is read as a British gauge.

Typical uses are checking whether a bundle needs a forklift or two people, turning a price per kilogram into a price per sheet, and estimating the dead load of cladding, guards and trays before choosing fixings.

  • Ten material presets with typical published densities, plus custom density
  • Thickness by value or by gauge from five gauge tables, including British SWG
  • Round holes and rectangular cut-outs subtracted
  • Weight per piece, batch total, kg/m² and lb/ft²
  • Same-size weight in every other material, copy and share link
Read the guide: How to Calculate Sheet Metal Weight (and Why Gauge Tables Disagree)

Updated

How to use the Sheet Metal Weight Calculator

  1. Leave the units on metric and enter the length and width in millimetres.
  2. Type the thickness in mm, or choose "Gauge number", then the SWG table and the gauge.
  3. Pick the material; for something not listed, choose a custom density in kg/m³.
  4. Set the number of sheets and any round holes or rectangular cut-outs per sheet.

Worked examples

2500 x 1250 mm mild steel sheet, 2 mm

Input

2500 x 1250 mm, 2 mm, mild steel at 7,850 kg/m³

Output

49.06 kg per sheet, 15.7 kg/m², 3.125 m²

A quick check: kg/m² for steel is the thickness in mm times 7.85. Two people can carry this sheet, but a pack of twenty is close to a tonne.

The same sheet ordered as "16 gauge"

Input

2500 x 1250 mm, 16 SWG (0.064 in, 1.626 mm), mild steel

Output

39.88 kg per sheet, 12.76 kg/m²; twenty sheets 797.6 kg

Read as a US 16 gauge (1.519 mm) the same sheet would come out at 37.26 kg. If a quote, a drawing and a stock list mention "16 gauge", confirm which table each means, or ask for the thickness in mm.

Five 304 stainless panels with six 50 mm holes

Input

2000 x 1000 x 3 mm, stainless 304 at 7,930 kg/m³, six 50 mm holes, quantity 5

Output

47.3 kg each, 236.5 kg for five, 23.79 kg/m²

The six holes take out 0.0118 m² per panel, about 0.28 kg. For costing by weight, ask the stockholder whether they bill on theoretical weight like this or on the weighbridge.

Background and insight

The default densities are typical published values: 7,850 kg/m³ for carbon steel (the value used throughout EN 1993 and most steel tables), 7,930 kg/m³ for 304 stainless, 2,680 kg/m³ for 5052 aluminium, 2,700 kg/m³ for 6061, 8,890 kg/m³ for C110 copper and 8,530 kg/m³ for C260 cartridge brass, the last two from Copper Development Association data. Alloys vary by a percent or so, so a custom density is available.

Steel sheet gauges carry a built-in weight. The Manufacturers’ Standard Gauge was defined from weight, at 41.82 lb per square foot per inch of thickness, which corresponds to about 8,030 kg/m³. That is why a nominal 16 gauge sheet is listed in old tables at 2.5 lb/ft² while 0.0598 in at 7,850 kg/m³ comes to 2.44 lb/ft². The calculator uses the density you pick, so expect results about 2% below the traditional gauge weight tables for steel.

Real sheet is rarely exactly nominal. Mills roll to a thickness tolerance (ASTM A568 for carbon steel sheet, ASTM A480 for stainless) and sheets tend to be thinner at the edges than in the middle. For shipping and lifting, round up; for costing by weight, ask the supplier whether they invoice on theoretical or actual weight.

Common use cases

  • Freight and handling

    Know the weight of a bundle before booking a truck or choosing a lifting clamp or forklift.

  • Material costing

    Convert a price per kilogram or pound into a price per sheet or per part.

  • Structural and enclosure design

    Estimate the dead weight of cladding, guards, ducts and panels for supports and fixings.

  • Comparing materials

    See how much an aluminium or stainless version of a steel part would weigh before redesigning it.

Tips and limitations

  • Gauge numbers run backwards: the higher the number, the thinner the sheet. 18 SWG is 1.219 mm and 20 SWG is 0.914 mm.
  • Where you can, specify sheet in millimetres on drawings and orders. The current British Standard for wire and sheet sizes, BS 6722, is metric only, and metric thicknesses avoid the gauge mix-up altogether.
  • Theoretical weight ignores rolling tolerance and coatings, so round up when choosing lifting gear and slings.
  • For a folded part, weigh the flat blank from the bend allowance calculator rather than the outside dimensions.

Sources and further reading

  1. SWG to mm conversion chart, The Metal Store (UK). British stockholder table giving 16 SWG as 0.064 in, 1.626 mm.
  2. Steel material properties, Steel Construction Institute. Density and BS EN 10025 grades of structural steel used in the UK.
  3. Manual handling at work, Health and Safety Executive. Assessing loads such as sheets carried by hand.
  4. Standard wire gauge, Wikipedia. The 1883 Order in Council, BS 3737:1964 (since withdrawn) and BS 6722:1986, the current metric-only standard; full SWG table.

Frequently asked questions

How thick is 16 SWG in mm?

1.626 mm (0.064 in). The US Manufacturers' Standard Gauge 16 is 1.519 mm, so a "16 gauge" sheet from an American chart weighs about 7% less than a British 16 SWG sheet of the same size.

How much does a 2500 x 1250 sheet of 2 mm steel weigh?

49.06 kg at 7,850 kg/m³. The area is 3.125 m² and 2 mm steel weighs 15.7 kg/m².

What is the difference between SWG and the American sheet gauges?

SWG is the British Imperial Standard Wire Gauge, set in 1883 and used for wire, sheet and tube wall in the UK and the Commonwealth. US sheet steel uses the Manufacturers' Standard Gauge, stainless the US Standard Gauge, and aluminium the Brown & Sharpe gauge. The same number gives a different thickness in each, which is why the calculator lets you pick the table.

How thick are 18, 20 and 22 SWG?

18 SWG is 1.219 mm, 20 SWG is 0.914 mm and 22 SWG is 0.711 mm. In mild steel those weigh 9.57, 7.18 and 5.58 kg/m².

Does aluminium sheet use the same gauge in the UK?

Most aluminium sheet in the UK is sold in mm. If someone quotes a gauge, ask which table they mean: US charts use the Brown & Sharpe gauge for aluminium, which differs from SWG. A 2500 x 1250 x 1.5 mm sheet of 5052 weighs 12.56 kg.

Is there an in-depth guide to the Sheet Metal Weight Calculator?

Yes. “How to Calculate Sheet Metal Weight (and Why Gauge Tables Disagree)” covers the background, how it works, common pitfalls and worked examples. Read the full guide.