Australia version. Metric throughout: square metres, millimetres of compacted asphalt and tonnes, with council crossover rules as an example and prices in A$. US version
Asphalt Driveway Calculator (Tonnes)
Tonnes of hotmix asphalt for a driveway, crossover or car park from the area in m² and the compacted thickness, with price per tonne in A$ and truckloads.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Asphalt Calculator?
In Australia a black driveway is asphalt or hotmix, sometimes called bitumen, and the mix is bought by the tonne. This version works in square metres and millimetres. At the default compacted density of 2,320 kg/m³ each 10 mm of thickness weighs 23.2 kg per square metre, so a 40 mm layer on a 48 m² driveway is about 4.7 tonnes with a little extra.
The part of the driveway between your boundary and the road, the crossover or vehicle crossing, is council land and built to the council's specification. Council crossover specifications set the build-up, and some councils require concrete; Banyule's current specification asks for 100 mm or more of asphalt on 150 mm of compacted crushed rock where asphalt is approved. Enter your own area and thickness to check a quote.
- Rectangle, circle, triangle, trapezoid or known area
- Editable compacted density with typical ranges for hot mix
- Short tons and metric tonnes with automatic price conversion
- Spread rate, truckloads and a thickness comparison table
- Copy, share link and reset; nothing leaves your browser
Updated
How to use the Asphalt Calculator
- Choose imperial or metric and the shape of the area to pave.
- Enter the dimensions, or pick Known area and type the area from a site plan.
- Enter the compacted thickness and check the density against your supplier's mix data.
- Add a waste allowance for edges, low spots and handwork, usually 3 to 10%.
- Enter the price per ton or tonne and the truck capacity to see cost and loads, then copy the result.
Worked examples
Single driveway, 15 x 3.2 m at 40 mm
Input
48 m², 40 mm compacted, 2,320 kg/m³, 5% extra
Output
1.92 m³; 4.68 tonnes
Driveways that carry only cars are often laid thinner than roads; the tool's thickness table shows the tonnes for 40 to 100 mm side by side.
Double driveway, 15 x 6 m at 50 mm
Input
90 m², 50 mm compacted, 2,320 kg/m³, 5% extra
Output
4.5 m³; 10.96 tonnes
About two 10 tonne truckloads. A thicker layer suits a driveway that takes a trailer, a caravan or the odd delivery truck; the base underneath still has to carry the load.
Background and insight
Asphalt plants and agency specifications describe placement as a spread rate. At 145 lb/ft³, one square yard one inch thick is 9 x (1/12) x 145 = 108.75 lb, which is why estimators use about 110 lb per square yard per inch. The same rule in metric is about 23 kg per square metre for each 10 mm. Compacted density, not the loose density in the truck, is what matters: the paver lays the mat loose and the rollers compact it by roughly 20 to 25% in thickness to reach the target air voids, typically around 7% in place for dense-graded mixes.
US suppliers quote short tons of 2,000 lb; most other countries use metric tonnes of 1,000 kg, and 1 tonne is 1.102 short tons. The calculator converts the price and truck capacity when you switch units so a quote stays comparable. Residential driveways are commonly 2 to 3 in (50 to 75 mm) of surface course on a compacted aggregate base; parking lots and roads carrying trucks need a pavement design, for example by the AASHTO method.
Common use cases
Driveway quotes
Check that a contractor's tonnage matches the area and thickness they propose.
Patching and overlays
Order the right amount of hot mix or cold patch for potholes and trench reinstatement.
Parking lots and site roads
Compare a 2 in and a 3 in surface course in tonnage and cost.
Trucking plans
Work out how many loads to schedule so the paver is never waiting for material.
Tips and limitations
- Apply to your council for a vehicle crossing permit before building or replacing a crossover; councils set the width, levels and materials.
- Spray seal (a bitumen spray with aggregate) is cheaper than asphalt on rural driveways but is priced per m², not per tonne.
- The compacted base matters as much as the asphalt: Banyule's crossover specification uses 150 mm of compacted crushed rock.
Sources and further reading
- Specification for construction of private/commercial vehicular crossing, Banyule City Council. Current version: where asphalt is approved, 100 mm or more on 150 mm of compacted crushed rock.
- Driveway technical standards, Brisbane City Council
Frequently asked questions
How many tonnes of asphalt do I need for my driveway?
Area in m² x thickness in metres x 2.32, plus 5 to 10% extra. A 48 m² driveway at 40 mm needs about 4.7 tonnes with 5% extra; at 30 mm, about 3.5 tonnes.
How thick should an asphalt driveway be?
It depends on the base and the vehicles. Council crossover specifications set the build-up, and some councils require concrete; Banyule's current specification asks for 100 mm or more of asphalt on 150 mm of compacted crushed rock where asphalt is approved. Heavier vehicles need a thicker layer designed for the load.
How much does a tonne of asphalt cover?
At 2,320 kg/m³, a tonne covers about 10.8 m² at 40 mm, 8.6 m² at 50 mm and 4.3 m² at 100 mm.
Is bitumen the same as asphalt?
Bitumen is the binder. Asphalt (hotmix) is stone and sand bound with bitumen and rolled while hot; a spray seal is bitumen sprayed on and covered with aggregate. People often call either one a bitumen driveway.
Do I need council approval for a driveway crossover?
Usually yes. The crossover sits in the road reserve, so councils require a permit and build it to their own specification and inspection.
Is there an in-depth guide to the Asphalt Calculator?
Yes. “Asphalt Tonnage: From Square Feet and Inches to Tons of Hot Mix” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.