Australia version. Metric for Australian decks: 90 x 19 or 140 x 19 boards in 5.4 m lengths, joists at 450 mm on bearers, decking screws per m² and prices in A$. US version

Decking Calculator (Australia)

Work out merbau or treated pine decking boards, joists at 450 mm, bearers, posts and screws for a deck in metres, with board costs in A$ and the NCC balustrade rule.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Deck Calculator?

Australian timber decks commonly use 90 x 19 or 140 x 19 mm hardwood boards such as merbau or spotted gum, or treated pine, laid on joists that sit on bearers and posts or stumps, at the spacing the span tables or the board supplier give. This version starts with a 5.4 x 3.6 m deck against the house in 90 x 19 boards bought in 5.4 m lengths.

Board width changes more than the look. The same deck takes 43 boards and about 1,014 screws in 90 mm boards, but 28 boards and 650 screws in 140 mm boards, because every extra row means another screw at every joist. Compare the two before you choose.

A deck that is 1 m or more above the ground needs a barrier: the NCC requires one wherever people could fall 1 m or more, and Part 11.3 of the ABCB Housing Provisions is the deemed-to-satisfy route. The deck framing itself is timber framing under the NCC, built to AS 1684 or designed by an engineer.

  • Rows and boards by stock length, with nesting of short rows
  • Straight or diagonal decking and adjustable waste
  • Joists, rim, ledger, beam plies, posts and hangers
  • Face screws or hidden clips per crossing, with boxes and rate per area
  • Cut list, joist span readout, decking cost, metric and imperial
Read the guide: Estimating a Deck: Boards, Joists, Screws and Span Tables

Updated

How to use the Deck Calculator

  1. Choose imperial or metric and enter the deck length along the house and the projection out from it.
  2. Enter the actual board width, the gap between boards and the board length you will buy, then choose straight or diagonal boards.
  3. Set the joist spacing, joist size label and stock length, the rim thickness, and whether a ledger attaches the deck to the house.
  4. Enter the beams, plies, posts and the joist cantilever past the beam from your design or permit drawing.
  5. Choose face screws or hidden clips, the count per box and the waste, then read the materials and cut list.

Worked examples

5.4 x 3.6 m merbau deck in 90 x 19 boards

Input

90 mm boards, 4 mm gaps, 5.4 m lengths, joists at 450 mm, ledger at the house, one bearer of two plies on three posts, 10% extra, A$30 a board

Output

39 rows, 43 boards (210.6 m net); 13 joists at 3555 mm; 1014 screws (about 52 per m², 3 boxes of 500); A$1,290 of boards

Hardwood boards are usually face-fixed with two screws per joist and pre-drilled. Joist and bearer sizes come from AS 1684 or the supplier's span tables.

The same deck in 140 x 19 boards

Input

140 mm boards at A$45 a board, everything else the same

Output

25 rows, 28 boards (135 m net); 650 screws (about 33 per m²); A$1,260 of boards

Fewer, wider boards cost about the same in timber but save more than 350 screws and the time to drive them. Wide boards cup more as they dry, so follow the supplier's fixing advice.

Background and insight

Joists are counted like studs: ceil(length / spacing) + 1 including both end joists. Rows of decking are ceil(projection / (board width + gap)), using the actual width. A 5/4x6 board is 5-1/2 in wide, so with a 3/16 in gap each row covers 5-11/16 in. When the deck is shorter than the boards, rows nest two or more to a board; when it is longer, butt joints have to land on joists and each row takes more than one board. Two face screws per board at every joist is the standard pattern, a little over 3 screws per square foot for 5-1/2 in boards at 16 in, and hidden clips use one per crossing.

Joist sizes and spans are a code question. In the US, IRC Section R507 holds the deck joist and deck beam span tables, which depend on species, grade, spacing and cantilever, and the American Wood Council publishes the same rules as DCA 6. Composite decking makers often require 12 in joist spacing for diagonal boards. The calculator shows your joist span so you can compare it with the table, but it does not size members.

Common use cases

  • Pricing a deck before a permit

    Get board, joist and fastener counts to compare composite and timber quotes.

  • Planning a resurface

    Count new boards and screws for existing framing by entering the deck size and joist spacing.

  • Choosing board direction

    Compare straight and diagonal layouts for board count, waste and fasteners.

  • Ordering stock lengths

    Try 12, 16 and 20 ft boards to find the length that nests best with your deck size.

Tips and limitations

  • Seal or oil hardwood boards before laying, and coat the cut ends, to slow surface checking and tannin bleed onto paving.
  • In termite-prone areas, keep timber posts on stirrups clear of the ground and leave the subfloor open for inspection.
  • Leave a gap between the deck and the house wall so water and leaves can drain, and keep the deck below the weep holes.

Sources and further reading

  1. NCC 2025 Volume Two, Part H5 Safe movement and access, Australian Building Codes Board. H5P2 barriers where people could fall 1 m or more; H5D3 points to Housing Provisions Part 11.3.
  2. NCC 2025 Volume Two, Part H1 Structure, Australian Building Codes Board. Timber framing to AS 1684 (H1D6).

Frequently asked questions

How many decking boards do I need for a 5.4 x 3.6 m deck?

In 90 mm boards with 4 mm gaps the 3.6 m width takes 39 rows; with 5.4 m lengths each row is one board, so 39 plus 10% gives 43. In 140 mm boards it is 25 rows and 28 boards.

What joist spacing do I need for 19 mm decking?

The maximum spacing depends on the species, grade and board thickness; take it from AS 1684 or the board supplier, and use closer joists for diagonal boards. The calculator opens at 450 mm centres as a starting point.

When does a deck need a balustrade?

The NCC requires a barrier wherever people could fall 1 m or more from a floor, including a deck. Part 11.3 of the ABCB Housing Provisions sets out how to build it. Your council or a building surveyor can tell you whether the deck itself needs approval.

Should I use merbau or treated pine?

Merbau and other hardwoods are harder wearing and more stable but cost more and need pre-drilling. Treated pine is cheaper and easy to work, and needs the right hazard level of treatment for above-ground or in-ground use. Joists and bearers are often treated pine even under hardwood boards.

How many screws per square metre of decking?

With two screws at each joist on joists at 450 mm, 90 mm boards take about 52 per m² and 140 mm boards about 33 per m² over a whole deck. The calculator counts the crossings for your size.

Is there an in-depth guide to the Deck Calculator?

Yes. “Estimating a Deck: Boards, Joists, Screws and Span Tables” covers the background, how it works, common pitfalls and worked examples. Read the full guide.