United Kingdom version. Petrol rather than gasoline, fuel pressure in bar and injector flow in cc/min by default, with UK pump fuel and remap practice in mind. US version
Fuel Injector Size Calculator (UK)
Size fuel injectors for a bhp target in cc/min with fuel pressure in bar, for petrol, E85 or methanol, and see what your current injectors will support.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Fuel Injector Size Calculator?
UK tuners usually talk about injector flow in cc/min and fuel pressure in bar, and injector flow ratings are often quoted at 3 bar (43.5 psi); check your injector's data sheet. This version starts there: a 300 bhp turbocharged four on petrol, four injectors held to 80% duty, and injectors rated at 3 bar. The answer is about 591 cc/min each at 3 bar, or 511 cc/min if the rail runs at 4 bar.
Bhp in the UK is the same mechanical horsepower the formula uses, so a rolling-road figure goes straight in. If the sheet gives wheel power, choose Wheels and set the drivetrain loss. For a car whose figure is in PS or kW, use kW, or convert PS at 0.986 hp each.
- Injector size from hp or kW, crank or wheel power
- BSFC presets for naturally aspirated, blower and turbo engines on gasoline, E85 and methanol
- lb/hr, cc/min and g/min with fuel specific gravity
- Square-root pressure correction to the injector's rated pressure
- Reverse mode: horsepower supported by a given injector
- Common injector sizes and a shareable link
Updated
How to use the Fuel Injector Size Calculator
- Enter the target power in hp or kW and say whether it is at the crank or the wheels. For wheel power, set the drivetrain loss.
- Choose the induction type and fuel to load a typical BSFC, or type your own BSFC from dyno data.
- Set the number of injectors (usually one per cylinder) and the maximum duty cycle you are willing to run.
- Enter the pressure the injector is rated at and the fuel pressure it will see in use.
- Read the required flow per injector and the rating to buy, then use the second panel to check what a given injector size supports.
Worked examples
300 bhp turbo four at 3 bar
Input
300 bhp at the crank, turbo, BSFC 0.60, 4 injectors, 80% duty, rated and run at 3 bar
Output
56.3 lb/hr, 591 cc/min per injector; next common size 650 cc
300 x 0.60 = 180 lb/hr of petrol in total, shared by four injectors open no more than 80% of the time.
Same engine with the rail at 4 bar
Input
As above, fuel pressure in use 4 bar
Output
Buy 511 cc/min rated at 3 bar; pressure factor 1.155
Flow rises with the square root of pressure, so raising the rail from 3 to 4 bar lets a smaller rated injector do the job, as long as the pump keeps up.
What a set of 440 cc injectors supports
Input
4 x 440 cc/min at 3 bar, turbo BSFC 0.60, 80% duty
Output
About 223 bhp at the crank (167 kW), 190 bhp at the wheels with 15% loss
A quick check before a stage 2 remap: if the target is well above this, the injectors, not the turbo, set the ceiling.
Background and insight
BSFC is the mass of fuel an engine burns per unit of power per hour, in lb/hp·hr. A healthy naturally aspirated gasoline engine at full load uses about 0.45 to 0.50, an engine with a belt-driven blower 0.55 to 0.60 and a turbocharged engine 0.60 to 0.65, because boosted engines run richer and with more charge cooling from the fuel. Multiplying crank horsepower by BSFC gives the total fuel flow; dividing by the number of injectors and by the fraction of time each one may stay open (duty cycle) gives the flow each injector must deliver. Tuners keep peak duty at or below 80 to 85% so the injector has time to close and the fuel system has margin.
Alcohol fuels carry less energy per pound. E85 needs roughly 30 to 40% more fuel than gasoline for the same power (its stoichiometric air-fuel ratio is about 9.8 against 14.7), and methanol about twice as much (stoichiometric about 6.4). The calculator scales the gasoline BSFC by 1.4 for E85 and 2.2 for methanol. Injector ratings are usually given in lb/hr or cc/min at a stated pressure, often 3 bar (43.5 psi). The trade conversion of 10.5 cc/min per lb/hr assumes a fuel specific gravity of about 0.72; the calculator uses 0.72 for gasoline, 0.78 for E85 and 0.79 for methanol.
Injector flow follows the orifice law: it rises with the square root of the pressure difference across the injector. An injector rated at 43.5 psi flows √(58 ÷ 43.5) = 1.155 times as much at 58 psi. With a 1:1 rising-rate regulator the pressure difference stays constant under boost, so the base pressure is the one to enter. Real injectors depart from the square-root law at the extremes and their dead time changes with pressure and battery voltage, which is why tuners use the injector maker's characterisation data in the ECU.
Common use cases
Turbo and blower builds
Size injectors before adding boost so the engine never runs lean at the top of the rev range.
E85 and flex-fuel conversions
See how much bigger the injectors must be to make the same power on ethanol.
Checking an existing setup
Find the power ceiling of stock or used injectors before a tune.
Engine swaps and EFI conversions
Pick injectors for a carburettor-to-EFI kit or a swapped engine with a different cylinder count.
Tips and limitations
- Standard UK unleaded is E10 and super is E5. The petrol preset assumes ordinary petrol; leave margin rather than sizing exactly to the limit.
- Remapped and modified cars must still pass the MOT emissions test, and a lean or rich map can fail it.
- Tell your insurer about engine modifications such as larger injectors, a remap or a bigger turbo; an undisclosed change can affect a claim.
- Compare injector ratings at the same pressure. Ratings are often quoted in cc/min at 3 bar (43.5 psi); check your injector's data sheet.
Sources and further reading
- E10 petrol explained, Department for Transport. UK standard (E10, 95 octane) and super (E5, 97+) grades
- MOT inspection manual: cars and passenger vehicles, section 8.2 Exhaust emissions, DVSA
- Fuel Properties Comparison, US Department of Energy Alternative Fuels Data Center. Energy content of petrol, E85 and methanol
Frequently asked questions
What size injectors do I need for 300 bhp?
On a turbocharged four running petrol at 80% duty and 3 bar, about 591 cc/min each, so a 650 cc injector leaves margin. A naturally aspirated engine needs less because its BSFC is lower.
Is bhp the same as hp in the calculator?
Yes. Brake horsepower is the mechanical horsepower measured at the flywheel (745.7 W), which is what the calculator uses. Metric PS is slightly smaller (735.5 W), so 300 PS is about 296 bhp.
What fuel pressure do UK cars run?
Many port-injected petrol engines run a few bar at the rail; check your car's data or fit a gauge and measure it. Direct-injection engines run at far higher pressures and use different injectors that this calculator does not size.
Does E10 need bigger injectors than E5?
Only slightly. Ethanol carries less energy than petrol, so a 10% blend needs a little more fuel for the same power. That is small next to the duty-cycle margin; sizing to 80% duty covers it.
Can I run E85 in the UK?
GOV.UK's petrol guidance covers the E10 and E5 grades sold at forecourts; E85 is not one of them. If you do run E85, choose it in the fuel list; it needs about 40% more fuel by mass, which is roughly 30% more injector flow (cc/min) than petrol.
Is there an in-depth guide to the Fuel Injector Size Calculator?
Yes. “Fuel Injector Sizing: BSFC, Duty Cycle and Fuel Pressure” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.