United Kingdom version. Metric inputs by default, with UK pump fuel in mind: standard unleaded is 95 octane E10 and super is 97+ octane E5. US version

Compression Ratio Calculator (Metric)

Static and dynamic compression ratio in millimetres and cc, for engines built to run on UK 95 RON E10 or 97+ super unleaded, with head skim and gasket effects.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Compression Ratio Calculator?

UK pumps sell petrol by research octane number (RON): standard unleaded has been 95 octane E10 since September 2021 in Great Britain and November 2022 in Northern Ireland, and the super grade is 97 or more and stays E5. American guides quote octane as the pump average (AKI), which reads several points lower for the same fuel, so a "91 octane" US build figure is not the same as 91 RON here.

This version starts in millimetres with a two-litre, 86 x 86 mm four. Enter the head chamber volume in cc, the gasket bore and compressed thickness, deck height and piston dish, and it adds up the clearance volume and returns the static ratio. Turn on dynamic compression with the rod length and the cam's intake closing angle to see what the engine actually squeezes.

  • Static compression from bore, stroke, chamber, gasket, deck and piston volumes
  • Dynamic compression from rod length and intake valve closing, using slider-crank geometry
  • Breakdown bar of every part of the clearance volume
  • Chamber volume needed for a target ratio, plus what ±2 or ±4 cc and a thicker gasket would do
  • Inch or millimetre inputs, copy and share link
Read the guide: Static vs Dynamic Compression Ratio: How to Calculate Both

Updated

How to use the Compression Ratio Calculator

  1. Choose inches or millimetres and enter bore and stroke.
  2. Enter the combustion chamber volume in cc, measured or from the head maker.
  3. Enter the head gasket bore and its compressed thickness, then the deck clearance (positive if the piston sits below the deck at TDC).
  4. Enter the piston volume: dish and valve reliefs as a positive number, a dome as negative.
  5. Read the static ratio and the breakdown of clearance volume. Switch on dynamic compression and enter rod length and intake closing angle (degrees after BDC) to see the dynamic ratio.
  6. Optionally enter a target ratio to see the chamber volume that would give it.

Worked examples

Two-litre four on standard gaskets

Input

86 x 86 mm, 45 cc chamber, 87 mm x 0.7 mm gasket, 0.2 mm deck, 5 cc dish, 143 mm rod, intake closes 45° ABDC

Output

Static 10.03:1, dynamic 9.05:1; gasket 4.16 cc of the clearance

A ratio around ten is typical of naturally aspirated road engines meant for 95 RON. The target field shows that 11:1 would need a 39.6 cc chamber.

Skimming the head by 3 cc

Input

Same engine, chamber reduced to 42 cc

Output

Static 10.55:1, dynamic 9.51:1

A head skim after a gasket failure raises compression by half a point here. If the engine was mapped for 95 RON, that is when owners start choosing super unleaded or a thicker gasket to bring it back.

Lowering compression for a turbo build

Input

77 x 85.8 mm, 40 cc chamber, 78 mm x 0.8 mm gasket, 0.3 mm deck, 12 cc dish, 140 mm rod, 40° ABDC

Output

Static 7.98:1, dynamic 7.39:1

Boosted builds on UK pump fuel commonly start from a low static ratio and rely on the map and boost level. A 9:1 target would need a 32.7 cc chamber with these pistons.

Background and insight

Static compression ratio is (swept volume + clearance volume) / clearance volume. Swept volume is π/4 x bore² x stroke for one cylinder. Clearance volume is everything left above the piston at TDC: the chamber in the head, the cylinder of gasket (π/4 x gasket bore² x compressed thickness), the deck volume (π/4 x bore² x deck clearance), and the piston crown shape. In this calculator a dish or valve relief is entered as a positive volume because it adds space, and a dome as negative because it takes space away. A piston that rises above the deck at TDC has a negative deck clearance.

Dynamic compression accounts for the intake valve staying open after bottom dead centre. Until it closes, the rising piston pushes charge back into the port, so compression only really starts at intake valve closing (IVC). The calculator finds the piston position at a crank angle of 180° plus the IVC figure using slider-crank geometry, x = r + l − (r cos θ + √(l² − r² sin² θ)), where r is half the stroke and l the rod length, and uses the remaining travel as the effective stroke. Use the seat-to-seat (advertised) IVC from the cam card; a common rule of thumb is to add about 15° to the 0.050 in figure if that is all you have.

As rough guidance from engine builders, iron-headed street engines on premium pump fuel are usually kept near 8 to 8.5:1 dynamic, with aluminium heads tolerating a little more. These are rules of thumb, not limits: chamber shape, quench, ignition timing, fuel and boost all shift them.

Common use cases

  • Choosing heads, pistons and gaskets

    Compare chamber sizes, gasket thicknesses and piston volumes to land on a target ratio before ordering parts.

  • Matching a camshaft

    Check that the static ratio and the cam's intake closing give a dynamic ratio suited to the fuel you will run.

  • Rebuilding a stock engine

    Work out what milling the heads or decking the block will do to compression after machining.

  • Boost planning

    Pick a lower static ratio for a turbocharged or blown build and see how the parts choices get there.

Tips and limitations

  • Use the compressed thickness printed on the gasket packet. On the two-litre example every extra 0.1 mm of gasket adds about 0.6 cc of clearance volume.
  • If a car's handbook asks for 95 RON, standard E10 meets it. Raising compression above standard is a reason to consider the 97+ super grade, but the knock limit depends on the chamber, timing and map, not on the ratio alone.
  • Older cars may not be warranted for E10. GOV.UK has a vehicle checker; those cars should stay on super grade E5.
  • Engine changes can affect your insurance, and a modified engine still has to pass the MOT emissions test.

Sources and further reading

  1. E10 petrol explained, Department for Transport. E10 at 95 octane, E5 super at 97+, and when E10 was introduced
  2. Check if your vehicle can use E10 petrol, GOV.UK
  3. Internal Combustion Engines (course 2.61), MIT OpenCourseWare. Compression ratio, knock and octane rating

Frequently asked questions

What octane is standard petrol in the UK?

95 RON. GOV.UK says standard grade petrol became E10 (95 octane) in Great Britain in September 2021 and in Northern Ireland in November 2022, and that E5 in the 'super' grade (97+ octane) is available from most filling stations.

Is UK 95 octane the same as US 91 octane?

Roughly. The UK quotes research octane (RON); US pumps show the average of research and motor octane, which is several points lower for the same fuel. A US premium of 91 to 93 at the pump is in the same range as UK 95 to 99 RON.

How much does skimming a head raise compression?

It depends on how many cc come out of the chamber. On the two-litre example, losing 3 cc from a 45 cc chamber lifts static compression from 10.03 to 10.55:1. Measure the chamber after machining rather than estimating from the depth cut.

Can I run higher compression on super unleaded?

Higher octane gives more knock margin, so engines built with more compression often need the 97+ grade. How much more the engine tolerates depends on chamber design, ignition timing and the ECU map, so treat any ratio as a starting point and check on a dyno with knock monitoring.

Does E10 change what compression ratio I can use?

E10 is sold at the same 95 RON minimum as the E5 it replaced, so a standard engine's compression does not need to change. The calculator works out the ratio; it does not model fuel.

Is there an in-depth guide to the Compression Ratio Calculator?

Yes. “Static vs Dynamic Compression Ratio: How to Calculate Both” covers the background, how it works, common pitfalls and worked examples. Read the full guide.