United Kingdom version. Starts in mph at the 70 mph motorway limit with a five-speed manual and a 195/65 R15 tyre, and explains the speedometer rules that apply to cars on UK roads. US version

Gear Speed Calculator (UK)

Engine revs at 70 mph and road speed in every gear from your gearbox ratios, final drive and tyre size, in mph, with what a tyre size change does to the speedometer.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Gear Speed Calculator?

The question most UK drivers bring here is how many revs the engine turns at 70 mph, the national speed limit on motorways and dual carriageways. With a five-speed manual geared 3.55, 1.90, 1.28, 0.97 and 0.76, a 4.06 final drive and 195/65 R15 tyres, the answer is 2,906 rpm in fifth and 3,709 rpm in fourth. Enter the ratios from the handbook or a gearbox code lookup and the table gives the same for every gear.

Changing wheel or tyre size changes all of it. A tyre with a larger rolling diameter turns fewer times per mile, so the car goes faster at the same revs and the speedometer under-reads. Every UK car must have a speedometer reading in mph and km/h, and type-approved cars meet ECE Regulation 39, under which a speedometer may read high but never below true speed, so they are set to read a little fast; a bigger tyre can use up that margin.

Speeds here assume no clutch slip and the unloaded tyre size. A loaded tyre rolls a few per cent smaller, so real road speed at a given rpm is slightly lower than the table.

  • Tyre diameter from metric codes (P, LT and ZR included), flotation sizes or a typed diameter
  • Up to eight gear ratios plus final drive and redline
  • Speed per gear at any rpm and at redline, rpm at a cruise speed, rpm after each upshift
  • rpm versus speed chart for every gear with redline and cruise markers
  • km/h or mph, copy results and share link
Read the guide: Road Speed from RPM, Gear Ratio and Tire Size: The Formula

Updated

How to use the Gear Speed Calculator

  1. Choose km/h or mph, then enter the tyre size code or switch to diameter and type it in inches or millimetres.
  2. Enter each gear ratio; add or remove gears to match the gearbox (up to eight).
  3. Enter the final drive (axle or differential) ratio and the redline.
  4. Enter a cruise speed and an engine speed of interest.
  5. Read the table: speed at your rpm and at redline in each gear, rpm at the cruise speed, and rpm after each upshift. The chart shows the same thing graphically.

Worked examples

Five-speed manual at 70 mph

Input

Ratios 3.55, 1.90, 1.28, 0.97, 0.76; final drive 4.06; 195/65 R15; redline 6,200 rpm

Output

Fifth 2,906 rpm; fourth 3,709 rpm; third 4,895 rpm

Typical of a small petrol hatchback. Sitting in fourth on the motorway adds 800 rpm, which shows up in fuel consumption and noise.

Six-speed with a tall top gear

Input

Ratios 3.36, 2.07, 1.43, 1.00, 0.84, 0.56; final drive 3.42; 205/55 R16; 70 mph

Output

Sixth 1,811 rpm; fifth 2,717 rpm

A very tall top gear like this is built for economy; at 50 mph sixth is down to 1,294 rpm, low enough that many engines will need a downshift to accelerate.

Background and insight

The wheel turns at engine rpm divided by the overall ratio, which is the gear ratio times the final drive. Each turn moves the car one tyre circumference, π x diameter. So speed in km/h is wheel rpm x π x diameter (mm) x 60 / 1,000,000. In US units this reduces to the familiar mph = rpm x tyre diameter (in) / (gear x axle ratio x 336), where 336.13 is 63,360 inches per mile divided by 60π.

A metric tyre code gives the section width in millimetres, the aspect ratio as a percentage of that width, and the rim diameter in inches. Overall diameter is rim x 25.4 + 2 x width x aspect / 100 mm, so a 225/45R17 is 431.8 + 202.5 = 634.3 mm. That is the unloaded size. Under load the tyre flattens and rolls on a slightly smaller effective radius, and worn tread is smaller again, which is why makers publish revolutions per mile measured on a rolling tyre.

The rpm drop on an upshift is the shift rpm times the ratio of the next gear over the current one. Close-ratio gearboxes keep that drop small so the engine stays near peak power; wide ratios trade that for a tall top gear that keeps cruising rpm low.

Common use cases

  • Axle ratio and tyre swaps

    See how a different final drive or taller tyres change cruising rpm and the speed in each gear before buying parts.

  • Track and drag gearing

    Check the rpm drop between gears and whether a gear runs out before the end of a straight or the finish line.

  • Engine swaps

    Pair a new engine's redline and power band with the existing gearbox and axle.

  • Speedometer sanity checks

    Compare calculated road speed at a given rpm with what the speedometer shows after a tyre change.

Tips and limitations

  • Gearbox ratios and final drive are often listed in the owner's handbook or the technical data in the brochure; the gearbox code on the casing finds them for older cars.
  • Stay with the tyre sizes listed for your model unless you have checked the speedometer: a different overall diameter changes the reading, and wheel and tyre changes are a modification to tell your insurer about.
  • Use rev counter readings at a steady 70 mph on a flat road to check the result; a large mismatch usually means the final drive is different from the one entered.

Sources and further reading

  1. Speed limits, GOV.UK. National speed limits by road type and vehicle.
  2. The Road Vehicles (Construction and Use) Regulations 1986, regulation 35: speedometers, legislation.gov.uk. Speedometers must show mph and km/h, or comply with ECE Regulation 39.

Frequently asked questions

What rpm should a car do at 70 mph?

It depends on the gearing. Many petrol hatchbacks sit between about 2,500 and 3,500 rpm in top, diesels and cars with six or more speeds lower. Enter your ratios, final drive and tyre size to get the exact figure.

Do bigger tyres make my speedometer wrong?

Yes, a larger overall diameter makes the car travel further per wheel turn, so the speedometer reads lower than your true speed. Under ECE Regulation 39, which UK type-approved cars meet, a speedometer may over-read but must not under-read.

Is the UK speed limit on motorways 70 mph?

For cars and motorcycles, yes: 70 mph on motorways and dual carriageways, 60 mph on single carriageways, unless signs show a lower limit. Vans, lorries and vehicles towing have lower limits.

How do I calculate speed from rpm?

Divide engine rpm by the gear ratio and the final drive to get wheel rpm, then multiply by the tyre circumference. The calculator does this for every gear and shows the working.

Why is the speed in top gear at the redline so high?

That figure is the gearing limit only. Aerodynamic drag and rolling resistance stop most cars well before the engine can reach its redline in top.

Is there an in-depth guide to the Gear Speed Calculator?

Yes. “Road Speed from RPM, Gear Ratio and Tire Size: The Formula” covers the background, how it works, common pitfalls and worked examples. Read the full guide.