Australia version. Metres and litres, with the 15, 10, 4 and 1 litre tins sold in Australia, the spread rate in m² per litre from the tin, and lead and asbestos advice for older homes. US version
Paint Calculator (Australia)
Work out how many litres of paint a room needs in square metres and coats, then the 15, 10, 4 and 1 litre tins to buy, with spread rates and lead paint advice.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Paint Calculator?
Australian interior paint comes in 1, 4, 10 and 15 litre tins, not the 2.5 and 5 litre sizes sold in Europe, so this version buys in those sizes. A 4 by 3.6 metre bedroom with 2.4 metre walls has 32.6 square metres to paint after the door and window come off. Two coats at a spread rate of 16 m² per litre need 4.08 litres: a 4 litre tin and a 1 litre tin.
The tin size range changes the answer. With European tins the same room would be a 2.5 and two 1 litre tins. Here a large living area with its ceiling comes to 9.29 litres, which the calculator rounds to a single 10 litre tin rather than two 4s and a 1.
The spread rate is printed on the tin and data sheet. Dulux gives 16 m² per litre as the theoretical spread rate for Wash&Wear Low Sheen; that assumes a smooth, sealed surface, so use a lower figure for fresh plasterboard, bagged brick or a big colour change.
- Walls, ceiling or both, with doors, windows and other areas subtracted
- Separate coat counts for walls and ceiling, plus optional primer
- Shopping list in 5 gallon, 1 gallon and quart sizes, or 10, 5, 2.5 and 1 litre tins
- Imperial and metric inputs that convert when you switch
- Cost from your own can prices, copy and share link, all in the browser
Updated
How to use the Paint Calculator
- Measure the room in metres and enter the wall height. Standard internal doors are about 820 by 2040 mm, roughly 1.7 m².
- Choose walls, ceiling or both, and the number of coats.
- Enter the spread rate from the tin in m² per litre.
- Keep the tin sizes on 15, 10, 4 and 1 L, and add a sealer or undercoat coat for new plasterboard.
- Enter your tin prices to compare one 15 L tin with smaller tins.
Worked examples
Bedroom repaint, 4 m x 3.6 m
Input
2.4 m walls, 1 door (1.7 m²), 1 window (2.16 m²), 2 coats, 16 m²/L
Output
32.6 m² of wall; 4.08 L; buy a 4 L and a 1 L tin
Only 0.08 litres over a single 4 litre tin, so a careful painter might manage on one tin. The calculator never rounds down, because running out on the last wall means a second trip and possibly a different batch.
Open living area with the ceiling
Input
6 m x 4.5 m, 2.7 m walls, 2 doors of 1.7 m² and 2 windows of 3 m², walls and ceiling at 2 coats, 16 m²/L
Output
74.3 m² painted; 9.29 L; one 10 L tin
Ceiling paint is usually a different product, so in practice you would split this into 5.91 litres of wall paint and 3.38 litres of ceiling white: a 4 L and two 1 L tins, plus a 4 L tin.
Four bedrooms the same size
Input
4 rooms of 4 m x 3.6 m, walls only, 2 coats, 16 m²/L
Output
130.5 m² of wall; 16.31 L; a 15 L tin and two 1 L tins
At this volume the 15 litre tin is usually the cheapest per litre, and one batch keeps the colour even across the rooms.
Background and insight
Coverage is the number that matters most and the one people skip. Manufacturers state a spreading rate for one coat at the film thickness the paint is designed for, usually on a smooth, sealed surface. Rough or porous surfaces, bare drywall, fresh plaster and textured ceilings soak up more, so the real figure can fall to 250 square feet per gallon or lower. Big colour changes, especially light over dark, often need a third coat or a tinted primer. That is why the calculator lets you choose a surface preset or type the figure from your can.
Openings are subtracted by area. A standard interior door of 3 by 7 feet is 21 square feet and a 3 by 5 foot window is 15 square feet, which are the defaults. Painters often ignore small windows because cutting in around them uses nearly as much paint as the glass would have taken; subtracting them gives the leanest honest estimate, and the extra percentage puts some back.
Two coats are the norm for new colour on walls. The first coat hides most of the old colour and evens out porosity; the second gives the uniform sheen and colour the manufacturer tested. Ceilings in flat white over the same white are often fine with one coat.
Common use cases
Repainting a room
Check whether one gallon is enough or you need two before driving to the store, and avoid opening a second batch mid-wall.
New drywall
Add a primer coat with its own coverage figure so the primer and finish paint are bought together.
Whole-house quotes
Price several identical bedrooms at once and compare 5 gallon buckets against single gallons.
Ceilings only
Estimate ceiling white for a whole floor, where one coat over the same colour is often enough.
Tips and limitations
- Homes built before 1970 are the most likely to have lead paint. The Australian Government guide Lead Alert covers testing and safe preparation before sanding or scraping.
- If your home was built or renovated before 1990 it might contain asbestos, including in some wall and eave sheeting. Do not sand or drill suspect material.
- New plasterboard needs a sealer or undercoat before the top coats; add it as a primer coat with its own spread rate.
- Stir and combine tins of the same colour before you start, so every wall matches.
Sources and further reading
- Lead Alert: The six step guide to painting your home (5th edition), Australian Government. Lead paint risk in homes built before 1970 and safe surface preparation.
- Householders and home renovators, Asbestos and Silica Safety and Eradication Agency. Homes built or renovated before 1990 might contain asbestos.
- Wash&Wear Low Sheen, Dulux Australia. Product page; the Australian data sheet gives a theoretical spread rate of 16 m² per litre.
Frequently asked questions
How much paint do I need for a bedroom in Australia?
For a 4 by 3.6 metre bedroom with 2.4 metre ceilings, about 4 litres for two coats on the walls at 16 m² per litre, which is a 4 litre tin and possibly a 1 litre tin. Add about 1.8 litres for two coats on the ceiling.
How far does a 4 litre tin of paint go?
At 16 m² per litre, 64 m² for one coat or 32 m² for two coats. That is the walls of a standard bedroom. Rough surfaces and strong colour changes reduce the area.
Is it cheaper to buy a 10 litre or 15 litre tin?
Per litre the bigger tins are usually cheaper, but specials change that often. Enter the price of each tin size and the calculator totals its suggested mix so you can compare.
How do I know if my house has lead paint?
Houses built before 1970 are the most at risk, though later homes can also have it. Test kits and accredited laboratories can confirm it. The Lead Alert guide from the Australian Government explains how to prepare surfaces without spreading lead dust.
Do I need sealer on new plasterboard?
Yes. Bare plasterboard and set joints absorb paint unevenly, so a sealer or sealer undercoat goes on first. Enter it as one primer coat with the spread rate on its tin.
What is a spread rate on a paint tin?
It is the area one litre covers for one coat, in square metres per litre, at the film thickness the maker tested. It is a theoretical figure, so real coverage on porous or textured surfaces is lower.
Is there an in-depth guide to the Paint Calculator?
Yes. “How Much Paint Do I Need? Coverage, Coats and Cans” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.